Bull DPS7000/XTANOVASCALE 7000 180Rb 7 Скачать руководство пользователя страница 211

Страница: 211 / 258

Illustrated Parts Breakdown 6-3

Field Replaceable Units

Reference
Number

Description

Part Number

Front Bezel Assembly

525-01502-000

Peripheral Bay Blind Mate Board Assembly with attached power, wide SCSI,
IDE, and diskette cables

160-01572-000

Peripheral Bay Backplane Board

160-01573-000

Memory Module Board

NOTE:

Memory Boards returned for repair or replacement must have RAM

removed. Replacement boards will not include RAM. Extra parts returned
are not recoverable.

160-01567-000

Memory DIMMs: Refer to subsection “Memory Expansion” in this section.

I/O Riser Board

160-01570-000

I/O Carrier Board

160-015

-000

CMOS/RTC 3V Battery

(CR2450 available locally)

Network Option Boards: Refer to subsection “Network Option Boards” in this
section.

Raid Controllers and Cache: Refer to subsection “RAID Controllers and
Cache” in this section.

Host Bus Adapter: Refer to subsection “Host Bus Adapter” in this section.

AC/EMI Filter

320-01656-000

750 Watt Power Supply

313-01514-000

PCI Hot Plug LED Board

160-01569-000

CPU Cover

247-01675-000

Fan Bay and Cover

247-01677-000

Fan Assembly

306-01514-000

Midplane Board

160-01568-000

Heatsink, Pentium III Xeon 20MM

309-01518-000

Terminator Pentium II Xeon

1301970000

Pentium III Xeon Processor(s) Refer to subsection “Pentium Processors” in
this section.

Extraction Tool Mezzanine Board

247-01680-000

Cache Coherency Board

160-01566-000

Front Panel Board

160-01571-000

Mezzanine Board

NOTE:

Replacement boards do not include CPUs or Terminators.

160-01565-000

Profusion Carrier Board

160-01574-000

CPU Retention Latch

247-01674-000

LCD Cable Assembly with Bracket

320-01655-000

Lock Bar Mezzanine Board

247-01679-000

Содержание DPS7000/XTANOVASCALE 7000 180Rb 7



































































































































































































































































Результаты поиска

Содержание DPS7000/XTANOVASCALE 7000 180Rb 7

Отзывы:

Bull DPS7000/XTANOVASCALE 7000 180Rb 7, Руководство по обслуживанию, Страница: 211 / 258

Результаты поиска

Содержание DPS7000/XTANOVASCALE 7000 180Rb 7

Отзывы: