Bull DPS7000/XTANOVASCALE 7000 180Rb 7 Скачать руководство пользователя страница 116

Страница: 116 / 258

4-6

Disassembly and Reassembly

Look at the yellow fan failure LEDs to determine which fan is defective.

Insert your thumb and forefinger into the grasp holes of the failed fan.

Pull the fan straight up and out of its bay. Set it aside.

Replacing a Fan

Remove the new fan from its protective packaging.

Note:

Fans are keyed and can be inserted in only one

way. Be sure that the fan connector mates with the front
panel connector when aligning the fan in the fan bay.

Align the fan with the fan bay. See Figure 4-1.

Push straight down on the fan until it is fully seated in the bay.

Replace the fan array cover with its securing screw.

Reinstall the front bezel. See “Removing and Installing the Front Bezel”
later in this chapter.

OM10702

A. Fan cover screw
B. Fan

cover

C. Grasp

holes

D. Fan

Figure 4-1. Replacing a Fan

Содержание DPS7000/XTANOVASCALE 7000 180Rb 7



































































































































































































































































Результаты поиска

Содержание DPS7000/XTANOVASCALE 7000 180Rb 7

Отзывы:

Bull DPS7000/XTANOVASCALE 7000 180Rb 7, Руководство по обслуживанию, Страница: 116 / 258

Результаты поиска

Содержание DPS7000/XTANOVASCALE 7000 180Rb 7

Отзывы: