Bull DPS7000/XTANOVASCALE 7000 180Rb 7 Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 258

background image

Disassembly and Reassembly 4-3

!

When disassembling disconnect all options.

!

When handling boards or chips, touch the system unit frame to release
static.

!

Do not disassemble parts other than those specified in the procedure.

!

All screws are Phillips-head, unless otherwise specified.

!

Label all removed connectors. Note where the connector goes and in
what position it was installed.

!

On completion of any reassembly, plug in the power cords and power on
the system unit.

Hard disk drives are installed or removed at the front of the server. Follow the
procedures in this chapter to open the front bezel to gain access to the hard disk
drives. Power supplies are installed or removed from the rear of the server.
Procedures to add or remove power supplies are found later in this chapter. The
top cover must be removed when installing all other server options.

Contact your sales representative or dealer for a list of approved optional
peripheral devices.

Precautions

The following warnings and cautions apply throughout this chapter. Only a
technically qualified person should integrate and configure the system.

The only procedures that can safely be done with the system power on is
removing or installing (hot-swapping) an SCA drive/carrier assembly in one of
the SCSI hot-swap drive cages, hot-swapping a failed power supply, or hot
swapping a hot plug fan or PCI board. For any other procedures inside the
system, turn off system power and disconnect the AC power cord (s).

«
...
111
112
113
114
115
...
»

Содержание DPS7000/XTANOVASCALE 7000 180Rb 7



































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DPS7000/XTANOVASCALE 7000 180Rb 7

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 2

eserver pSeries 690

Бренд: IBM Страницы: 142

eServer 370 xSeries

Бренд: IBM Страницы: 218

BladeCenter PS703

Бренд: IBM Страницы: 298

BladeCenter T Type 8720

Бренд: IBM Страницы: 180

Adaptive Server IQ 12.4.2

Бренд: Sybase Страницы: 536

Бренд: Cobalt Digital Inc Страницы: 218

SuperWorkstation 740A-T

Бренд: Supermicro Страницы: 138

NovaScale R410B F2

Бренд: Bull Страницы: 38

Бренд: d3 Technologies Страницы: 10

SAT-IP EXIP 418

Бренд: Kathrein Страницы: 16

Бренд: TYAN Страницы: 77

SC450NX - Server Platform - 0 MB RAM

Бренд: Intel Страницы: 200

TERASTATION HS-D1.0TGL/R5

Бренд: Buffalo Страницы: 2

IP-DECT SERVER 6500

Бренд: SpectraLink Страницы: 126

Бренд: QNAP Страницы: 39

Бренд: EVS Страницы: 87

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды