Bull DPS7000/XTANOVASCALE 7000 180Rb 7 Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 258

Bull DPS7000/XTANOVASCALE 7000 180Rb 7 Скачать руководство пользователя страница 87

Configuring Your System 3-27

System Event Log (SEL) Viewer Add-in

Clicking on the SEL add-in task brings up the SEL viewer add-in, which allows
you to:

!

Examine SEL records via the baseboard management controller (BMC)
in hex or verbose mode.

!

Examine SEL records by sensor or event type in hex or verbose mode.

!

Examine SEL records from a previously stored binary file in hex or
verbose mode.

!

Save SEL records to a file in either text or binary form.

!

Clear SEL entries from the nonvolatile storage area.

The SEL viewer main window provides access to features of the add-in. Each
option included on the main menu supports an accelerator key. Accelerator
keys are indicated by an underlined letter in the text listing the option. The main
window includes support to display the following information for each SEL
entry:

!

Record identifier

!

Event type

!

Time stamp information

!

Generator identifier

!

Emv revision

!

Sensor type

!

Sensor number

!

Event description

«
...
85
86
87
88
89
...
»

Содержание DPS7000/XTANOVASCALE 7000 180Rb 7



































































































































































































































































Отзывы:

Нет отзывов