Buderus Logano G515 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 68

background image

Read carefully prior to installation and maintenance.

Installation and Service Instructions

Low-temperature
oil/gas boiler

Logano G515

6 720 642 624-00.1O

Boilers for oil/gas-fired power burners

6 7

20 647 208 (2014/09) US/CA

WARNING:

If installation, adjustment, modification,

operation or maintenance of the heating system is carried
out by an unqualified person, this may result in personal
injury or property damage.
The directions of this installation manual must be followed
precisely.
If support or additional information is required, contact a
qualified service company, service provider or the gas
company.

WARNING:

Observe the safety instructions of this installation manual
before placing the heating appliance in operation.
The operating manual is a component of the technical
documentation and must be handed over to the operator
of the heating system. Explain to the owner or operator
how to use the heating system using the operating instruc-
tions. Make sure that he has been familiarized with all
information required for the operation of the heating sys-
tem..

NOTICE:

If the storage tank will be installed in Massachu-

setts, it must be installed by an installer or dealer who is
registered there.

This manual is available in the English and French lan-
guage.

Please keep this manual for future reference.

1
2
3
...
»

Содержание Logano G515





































































Отзывы:

Нет отзывов

Похожие инструкции для Logano G515

Бренд: Ideal Boilers Страницы: 4

Бренд: IBC Страницы: 4

MURELLE HT 25 GPL

Бренд: Sime Страницы: 76

Бренд: Kenmore Страницы: 30

Бренд: Ariston Страницы: 44

Бренд: THERMO 2000 Страницы: 18

Бренд: THERMO 2000 Страницы: 22

Бренд: THERMO 2000 Страницы: 24

Бренд: THERMO 2000 Страницы: 32

Бренд: THERMO 2000 Страницы: 29

Бренд: IBC Страницы: 2

Бренд: Climit Страницы: 72

Бренд: Baxi Страницы: 8

Бренд: Baxi Страницы: 40

Mexico Super CF445

Бренд: Ideal Boilers Страницы: 4

Бренд: Atlantic Страницы: 56

Бренд: DOMUSA Страницы: 28

Бренд: Potterton Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды