BRP can-am COMMANDER 1000 2017 Скачать руководство пользователя страница 81

Страница: 81 / 155

FUEL

WARNING

If a differential pressure condition
is noticed (whistling sound heard
when loosening fuel reservoir cap)
have vehicle inspected and/or re-
paired before further operation.

4. Insert the spout into the filler neck.

5. Pour fuel slowly so that air can es-

cape from the tank and prevent fuel
flow back. Be careful not to spill
fuel.

6. Stop filling when the fuel reaches

the bottom of filler neck.

Do not

overfill.

WARNING

Never top up the fuel tank before
placing the vehicle in a warm area.
As temperature increases, fuel ex-
pands and may overflow.

7. Fully tighten fuel reservoir cap clock-

wise.

WARNING

Always wipe off any fuel spillage
from the vehicle.

Fueling a Gasoline
Container

WARNING

– Use only an approved gasoline

container to store fuel.

– Never fill the gasoline con-

tainer in the vehicle cargo box
or on-the vehicle - an electrical
static discharge may ignite the
fuel.

_______________

Содержание can-am COMMANDER 1000 2017




























































































































































Результаты поиска

Содержание can-am COMMANDER 1000 2017

Отзывы:

Бренды по названию

Популярные бренды

BRP can-am COMMANDER 1000 2017, Руководство оператора

Результаты поиска

Содержание can-am COMMANDER 1000 2017

Отзывы:

Бренды по названию

Популярные бренды