BRP can-am COMMANDER 1000 2017 Скачать руководство пользователя страница 61

Страница: 61 / 155

MULTIFUNCTION GAUGE (LCD) (DPS MODEL ONLY)

(1)

To erase the MAINTENANCE RE-

QUIRED message, proceed as fol-
lows:

1. Select PARK.

2. Turn ignition switch to ON. Do NOT

start engine.

NOTE:

The steps 3 through 9 must be

completed within

5 seconds

3. Press override switch and HOLD.

4. Press and release brake pedal.

5. Release override switch.

6. Press and release brake pedal.

7. Press override switch and HOLD.

8. Press and release brake pedal.

9. Release override switch.

10. Turn ignition switch to OFF

NOTE:

Do not turn ignition switch to

ON before the multifunction gauge
turns off.

Fault Code Mode

Press and hold mode button while
switching high and low beam (three cy-
cles) to access diagnostic fault codes.

Navigating in the LCD
Gauge

Default Display Mode

After vehicle startup, the default dis-
play mode is either:

– Vehicle speed
– Engine

revolutions

per

minute

(RPM)

– Both parameters simultaneously

(combined mode).

To change from one display to the
other, proceed as follows.

1. Turn ignition key to ON to power up

the system up.

2. Wait until the “greeting message”

has been displayed.

3. Press and release selector button

once to display OD (odometer).

4. Press the selector button again, this

time for 2 seconds.

This will change the Mode to either
Speed, RPM or Combined.

vdd2008-001-083

5. To select another mode, repeat

steps 3 and 4 until the desired mode
is displayed.

Temporary Display Mode

In the temporary display mode, the fol-
lowing functions are available:

– Odometer
– Clock
– Trip meter (resettable)
– Trip Hour meter (resettable)
– Engine hour meter.

Press and release selector button to
change the default display mode to the
temporary mode.

tmo2011-001-702_c

1. Selector button

The gauge will display the selected
mode for 10 seconds then will return
to the normal display mode.

While in a resettable mode, push and
HOLD selector button for 2 seconds to
reset it.

_______________

Содержание can-am COMMANDER 1000 2017




























































































































































Результаты поиска

Содержание can-am COMMANDER 1000 2017

Отзывы:

Бренды по названию

Популярные бренды

BRP can-am COMMANDER 1000 2017, Руководство оператора

Результаты поиска

Содержание can-am COMMANDER 1000 2017

Отзывы:

Бренды по названию

Популярные бренды