BRP can-am COMMANDER 1000 2017 Скачать руководство пользователя страница 105

Страница: 105 / 155

MAINTENANCE PROCEDURES

Remove the muffler cover.

tmo2011-001-040_a

1. Muffler cover
2. Exhaust tail pipe

Remove and discard the tail pipe retain-
ing screws.

tmo2011-001-045_a

1. Retaining screws

Remove exhaust tail pipe, gasket (dis-
card) and spark arrester.

tmo2011-001-041_a

1. Spark arrester
2. Gasket
3. Exhaust tail pipe

Remove carbon deposits from the
spark arrester using a brush.

NOTICE

Use a soft brush and be

careful to avoid damaging spark ar-
rester mesh.

tmo2011-001-043_a

1. Clean spark arrester

Inspect mesh of spark arrester for any
damage. Replace as required.

Inspect spark arrester chamber in muf-
fler. Remove any debris as required.

Reinstall the muffler spark arrester in
the reverse of the removal procedure.
However pay attention to the follow-
ing.

Install

new

gasket

and

retaining

screws. Torque to specification.

______________

103

Содержание can-am COMMANDER 1000 2017




























































































































































Результаты поиска

Содержание can-am COMMANDER 1000 2017

Отзывы:

Бренды по названию

Популярные бренды

BRP can-am COMMANDER 1000 2017, Руководство оператора

Результаты поиска

Содержание can-am COMMANDER 1000 2017

Отзывы:

Бренды по названию

Популярные бренды