Brother HL-2150N Скачать руководство пользователя

Страница: 50 / 177

1-35

Confidential

■

Ghost

■

Fogging

CAUTION:

This problem often occurs when the drum unit or toner cartridge is nearly at the end of life.

User Check

• Check the machine's environment, conditions such as high or low

humidity may cause this situation to occur.

• Check that the appropriate media type or size is selected in the

printer driver.

• Replace the drum unit with a new one.

Step

Cause

Check

Result

Remedy

HVPS PCB
failure

Is the problem solved
after replacing the
HVPS PCB ASSY?

Yes

Replace the HVPS PCB
ASSY.

Main PCB failure

Is the problem solved
after replacing the main
PCB ASSY?

Yes

Replace the main PCB
ASSY.

User Check

• Replace the toner cartridge with a new one.

• Replace the drum unit with a new one.

• Do not use acid paper.

• Check if there is dust or paper powder in the machine.

Step

Cause

Check

Result

Remedy

Toner sensor
failure (Machine
body)

Is the toner sensor
performed normally by
following the procedure
in

"Factory Inspection

Mode"

(Chapter 5).

Replace the toner sensor
PCB unit ASSY and the
toner LED PCB ASSY.

HVPS PCB
failure

Is the problem solved
after replacing the
HVPS PCB ASSY?

Yes

Replace the HVPS PCB
ASSY.

Main PCB failure

Is the problem solved
after replacing the main
PCB ASSY?

Yes

Replace the main PCB
ASSY.

Содержание HL-2150N


















































































































































































Результаты поиска

Содержание HL-2150N

Отзывы:

Похожие инструкции для HL-2150N

Бренды по названию

Популярные бренды

Brother HL-2150N, Руководство по обслуживанию

Результаты поиска

Содержание HL-2150N

Отзывы:

Похожие инструкции для HL-2150N

Бренды по названию

Популярные бренды