Brother HL-2150N Скачать руководство пользователя | Manualshive

Страница: 31 / 177

background image

1-16

Confidential

11) Memory full

Memory full

12) Print overrun

Data expansion is not in time

13) Main PCB failure

14) Fuser unit failure

CAUTION:

This problem will be cleared if leaving the machine power ON for ten minutes.

Turn the power on while pressing the SW supporter, when the front cover is open. And check
that Toner, Drum and Error LEDs light up, and then release the SW supporter.
Check that all LEDs go off and press the SW supporter once, and then this problem may be
cleared by that press the SW supporter once again after all LEDs light up.

User Check

• Press the [Go] button, then print the stored data.

• Reduce the data capacity or reduce the print resolution.

User Check

• Reduce the complexity of data or reduce the print resolution.

User Check

• Turn the power off and on.

Step

Cause

Remedy

1

Main PCB failure

Replace the main PCB ASSY.

Step

Cause

Remedy

1

Harness connection failure
between fuser unit connector and
eject sensor PCB ASSY

Check the harness connection between
fuser unit connector and eject sensor PCB
ASSY.

2

Fuser unit failure

Replace fuser unit.

3

Low-voltage power supply PCB
failure

Replace the PS PCB unit.

4

Toner LED PCB failure

Replace the toner LED PCB ASSY.

5

Main PCB failure

Replace the main PCB ASSY.

«
...
29
30
31
32
33
...
»

Содержание HL-2150N


















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HL-2150N

Sure shot 80 tele

Бренд: Canon Страницы: 24

iPF720 - imagePROGRAF Color Inkjet Printer

Бренд: Canon Страницы: 8

Бренд: Canon Страницы: 2

Бренд: Oki Страницы: 54

Бренд: Oki Страницы: 54

Бренд: Oki Страницы: 103

Бренд: Oki Страницы: 256

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 63

Бренд: Oki Страницы: 28

Бренд: Oki Страницы: 616

Бренд: Oki Страницы: 32

Бренд: Oki Страницы: 138

Microline 320 Turbo D1

Бренд: Oki Страницы: 2

ML320 Epson/IBM

Бренд: Oki Страницы: 32

Бренд: Oki Страницы: 32

Бренд: Oki Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды