Brother HL-2150N Скачать руководство пользователя | Manualshive

Страница: 160 / 177

background image

5-15

Confidential

■

Page 3, 4

These pages include various network settings information of the machine.

18) Sleep Mode Indication (OFF/Dimmed)

This is to select whether the Ready LED is turned off completely or lit in blue with low
light intensity during the Sleep mode. Whenever you switch this mode, the setting is
changed over from the present one to the other. When you take your finger off from the
SW supporter, the Ready LED is lit in 100% light intensity or low light intensity
according to the setting so that you can verify the present setting.

19) Sleep Mode Setting (ON/OFF)

This is to allow you to turn on and off the sleep mode of the machine. The default
setting is ON. The machine automatically goes back to the waiting Service mode state
after the operation is completed.

20) Developer Roller Counter Reset 1 (For the starter toner cartridge)

21) Developer Roller Counter Reset 2 (For the standard toner cartridge)

22) Developer Roller Counter Reset 3 (For the high-capacity toner cartridge)

Since print density is likely to become darker as toner is getting older, the developing
bias is lowered by degrees according to the number of prints so that an almost fixed
density can be maintained from the start of the use of brand-new toner to the end of it.

The value of the developing bias is printed on the maintenance sheet. The developing
bias is a parameter which depends on the developing assembly, so it needs to be reset
when the developing assembly is replaced. At that time, the developing roller counter
reading is also reset. This mode is to enable to execute these operations (equivalent to
those done when the developing assembly is replaced) manually from the service
mode.

HL-2150N/2170W

Page 3: Wired Network Information

HL-2170W

LAN: Wired Enable setting = ON, LAN: WLAN Enable setting = ON
Page 3: Wired Network Information
Page 4: Wireless Network Information

LAN: Wired Enable setting = ON, LAN: WLAN Enable setting = OFF
Page 3: Wired Network Information
Page 4: Not Available

LAN: Wired Enable setting = OFF, LAN: WLAN Enable setting = ON
Page 3: Wireless Network Information
Page 4: Not Available

LAN: Wired Enable setting = OFF, LAN: WLAN Enable setting = OFF
Page 3&4: Not Available

«
...
158
159
160
161
162
...
»

Содержание HL-2150N


















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HL-2150N

CLP 510N - Color Laser Printer

Бренд: Samsung Страницы: 270

Bixolon SRP-270

Бренд: Samsung Страницы: 13

Бренд: Oki Страницы: 2

OKIPAGE 8c Plus

Бренд: Oki Страницы: 48

Бренд: Oki Страницы: 257

Бренд: Oki Страницы: 113

Бренд: Oki Страницы: 26

Бренд: Oki Страницы: 183

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 136

Бренд: Oki Страницы: 66

Бренд: Oki Страницы: 123

Бренд: Oki Страницы: 109

Бренд: Oki Страницы: 68

Бренд: Oki Страницы: 12

Бренд: Oki Страницы: 22

Бренд: Oki Страницы: 22

Бренд: Oki Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды