Brother HL-2150N Скачать руководство пользователя страница 152 | Manualshive

Страница: 152 / 177

background image

5-7

Confidential

<Function>

Functions of each “Service Mode”.

9)

Factory Inspection Mode

This mode checks the operation of each sensor, solenoid, fan, scanner motor and main
motor to check the point with the malfunction, when repair the machine.

• The machine goes into the inspection mode by a special operation when the power is

turned on.

• In the inspection mode, the Ready LED blinks once when the state of a sensor or a

switch is changed (from ON to OFF, or from OFF to ON).

• The Toner LED is lit when the state of all switches and sensor is detected.

<Sensor Inspection Check Procedure>

• Check sensors.

Manually activate the sensors and the actuators listed below, and verify that the
Ready LED is lit. (The toner sensor can be activated by blocking the light sensor with
your hand.)
(When the state is changed continuously, the Ready LED keeps blinking.)
Cover sensor, New toner sensor, Registration rear sensor, Paper eject sensor,
Registration front sensor, Toner sensor and Tail edge sensor.
When the verification of all the sensors is completed the Toner LED becomes lit.

Fig. 5-1

Cover sensor

Cover sensor

harness ASSY

Toner sensor

(Toner LED PCB ASSY)

Paper eject sensor

(Eject sensor PCB ASSY)

New toner sensor

New toner sensor harness ASSY

Eject actuator

Registration front sensor

/Tail edge sensor

(Registration front sensor PCB ASSY)

Registration rear sensor

(Registration rear sensor PCB ASSY)

Toner sensor

(Toner sensor PCB unit ASSY)

Registration

front actuator

Edge actuator

Registration rear actuator

«
...
150
151
152
153
154
...
»

Содержание HL-2150N


















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HL-2150N

Бренд: F+D Feinwerk- und Drucktechnik Страницы: 41

Бренд: Oki Страницы: 320

Бренд: Xante Страницы: 31

Бренд: IBM Страницы: 142

Бренд: Hanin Страницы: 76

UniServer R6900 G5

Бренд: H3C Страницы: 17

Бренд: IESC Страницы: 109

Бренд: i3 International Страницы: 2

Бренд: TP-Link Страницы: 16

Бренд: Xerox Страницы: 34

Бренд: Fibrenetix Страницы: 17

SAT-IP EXIP 418

Бренд: Kathrein Страницы: 16

Бренд: ACE COMPUTERS Страницы: 32

Бренд: Synology Страницы: 24

Бренд: Xerox Страницы: 240

Accel-a-Writer 4

Бренд: Xante Страницы: 12

Бренд: ASROCK Страницы: 40

Intesis IBMBSDAL0640000

Бренд: HMS Networks Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды