Brother HL-2150N Скачать руководство пользователя страница 34

Страница: 34 / 177

1-19

Confidential

3.3

Paper Jam

■

Paper jam in the paper tray and front cover

■

Paper jam in the back cover and paper eject section

Step

Cause

Check

Result

Remedy

Registration front
actuator/edge
actuator catching
on some position

Does the registration front
actuator/edge actuator
move smoothly?

Re-assemble the
registration front actuator/
edge actuator.

Registration front
sensor PCB
(registration front
actuator/edge
actuator failure)

Does the registration front
sensor move smoothly?
(Check it following the
procedure described in

"Factory Inspection
Mode"

in Chapter 5)

Replace the registration
front sensor PCB ASSY.

Registration
solenoid failure

Is the problem solved
after replacing the
registration solenoid?

Yes

Replace the registration
solenoid.

Toner LED PCB
failure

Is the problem solved
after replacing the toner
LED PCB ASSY?

Yes

Replace the toner LED
PCB ASSY.

High-voltage
power supply PCB
failure

Is the problem solved
after replacing the High-
voltage power supply
PCB ASSY?

Yes

Replace the High-voltage
power supply PCB ASSY.

Registration
ground spring
loose

Is the registration ground
spring fitted correctly?

Fit the registration ground
spring correctly.
(Refer to

Fig. 1-4

Main PCB failure

Is the problem solved
after replacing the Main
PCB ASSY?

Yes

Replace the Main PCB
ASSY.

Step

Cause

Check

Result

Remedy

Foreign object
around fuser unit

Is there a foreign object
around the fuser unit?

Yes

Remove the foreign
object.

Paper eject
actuator failure

Does the paper eject
actuator move smoothly?
Is it damaged?

Replace the paper eject
actuator.

Fuser cover ASSY
loose

Is the fuser cover ASSY
fitted correctly?

Fit the fuser cover ASSY
correctly.

Outer chute ASSY
loose

Is the outer chute ASSY
fitted correctly?

Fit the outer chute ASSY
fitted correctly.

Eject roller 2
malfunction

Is each pinch roller of the
inner chute ASSY
attached to each eject
roller 2 of top cover ASSY
properly?

Replace the inner chute
ASSY.

Paper eject sensor
PCB failure

Is the problem solved
after replacing the paper
eject sensor PCB?

Yes

Replace the paper eject
sensor PCB ASSY.

Содержание HL-2150N


















































































































































































Результаты поиска

Содержание HL-2150N

Отзывы:

Похожие инструкции для HL-2150N

Бренды по названию

Популярные бренды

Brother HL-2150N, Руководство по обслуживанию

Результаты поиска

Содержание HL-2150N

Отзывы:

Похожие инструкции для HL-2150N

Бренды по названию

Популярные бренды