Brother HL-1070 Скачать руководство пользователя страница 200

Страница: 200 / 244

USER’S GUIDE

5–4

4. Remove the old toner cartridge from the drum unit by pulling it out

gently.

Fig. 5-5 Removing the Old Toner Cartridge

Caution

Handle the toner cartridge carefully. If toner scatters on your hands or
clothes, wipe or wash it off with cold water immediately.

5. Unpack the new toner cartridge, gently shake it five or six times and

then remove the protective part.

Caution

Only unpack the toner cartridge immediately before installing it into

the printer. If toner cartridges are left unpacked for a long period of
time, the toner life is shortened.

Never turn the black ring of the toner cartridge.

You can only use a Brother genuine toner cartridge which is

specially formulated to ensure top print quality. Using another
brand of toner cartridge could void your printer’s warranty.

Fig. 5-6 Shaking the Toner Cartridge

and Remove the Protective Part

Содержание HL-1070





















































































































































































































































Результаты поиска

Содержание HL-1070

Отзывы:

Бренды по названию

Популярные бренды

Brother HL-1070, Руководство по обслуживанию

Результаты поиска

Содержание HL-1070

Отзывы:

Бренды по названию

Популярные бренды