manualshive.com logo in svg

Brother DCP-9045CDN, Руководство по обслуживанию

Поделиться
Скачать
Brother DCP-9045CDN Скачать руководство пользователя страница 86

Confidential 

1-67

(10) Video signal reception 

Code 1 

Code 2 

Causes 

A0 

03 

Error correction sequence not terminated even at the final 
transmission speed for fallback. 

A0 

11 

Receive buffer empty. (5-second time-out) 

A0 

12 

Receive buffer full during operation except receiving into memory.

A0 

13 

Decoding error continued on 500 lines or more. 

A0 

14 

Decoding error continued for 10 seconds or more. 

A0 

15 

Time-out: 13 seconds or more for one-line transmission. 

A0 

16 

RTC not found or carrier OFF detected for 6 seconds. 

A0 

17 

RTC found but no command detected for 60 seconds or more.

A0 

19 

No video data to be sent 

A8 

01 

RTN, PIN, or ERR received at the calling terminal. * 

A9 

01 

RTN, PIN, or ERR received at the called terminal. * 

AA 

18 

Receive buffer full during receiving into memory. 

* Available in German models only 

(11) General communications-related 

Code 1 

Code 2 

Causes 

B0 

02 

Unable to receive the next-page data. 

B0 

03 

Unable to receive polling even during turn-around 
transmission due to call reservation. 

B0 

04 

PC interface error. 

BF 

01 

Communication canceled by pressing the 

Stop/Exit

 button 

before establishment of FAX communication*. 

BF 

02 

Communication canceled by pressing the 

Stop/Exit

 button 

after establishment of FAX communication*. 

BF 

03 

Transmission canceled due to a scanning error caused by no 
document or document feed problem in ADF scanning in real 
time transmission. 

* Establishment of FAX communication: 

FAX communication is established when the calling station receives a DIS (reception 
capability) signal from the called station and the called station receives a NSS or DCS 
(communications test) signal from the calling station. 

(12) Maintenance mode 

Code 1 

Code 2 

Causes 

E0 

01 

Failed to detect 1300 Hz signal in burn-in operation. 

E0 

02 

Failed to detect PB signals in burn-in operation. 

 

 

 

(13) Equipment error 

Code 1 

Code 2 

Causes 

FF X X Equipment 

error 

(For X X, refer to 

“2.1 Error Indication”

) 

 

 

 

Содержание DCP-9045CDN












































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды