manualshive.com logo in svg

Brother DCP-9045CDN, Руководство по обслуживанию

Поделиться
Скачать
Brother DCP-9045CDN Скачать руководство пользователя страница 383

Confidential 

5-23

1.4.15  Fine Adjustment of Scan Start/End Positions (Function code 54) 

<Function> 

This function allows you to adjust the scanning start and end positions with the ADF and FB 
unit.

 

<Operating Procedure> 

(1) Press 

the 

5

 and 

4

 buttons in this order in the initial stage of the maintenance mode. 

The “SCAN START ADJ.” will appear on the LCD. 

(2) The 

“ : ADF  : FB” will appear after two seconds. 

Select one of them that you want to adjust the start position. 
If you want to adjust the start position of the ADF, press   button, and if you want to 
adjust that of the FB unit, press   button. 

(3) Press 

the 

1 

or

 2

 button to display the present compensation level for the start position. 

Compensation levels can be adjusted in 11 steps from +5 to –5 (mm). 

(4) Press 

the 

 

button to increase compensation levels, and the   button to lower them. 

Press the 

Stop/Exit

 button so that the machine beeps for one second and returns to the 

initial state of the maintenance mode without adjusting compensation levels. 

(5)  Set the compensation level and press the 

OK

 button. 

The “ACCEPTED” will appear on the LCD. One second later, the machine “ : ADF  : 
FB” will appear on the LCD. 

(6) Press 

the 

Stop/Exit

 button when finish the adjustment. The machine beeps for one 

second and returns to the initial state of the maintenance mode. 

Note: 

The correlation between the scan start/end positions and compensation levels is shown below. 

 

Fig. 5-14 

Содержание DCP-9045CDN












































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды