Brother DCP-9045CDN Скачать руководство пользователя страница 267

Страница: 267 / 491

Confidential

3-134

Assembling Note:

When assembling the Paper feed frame unit, make sure to follow the procedure described
below.

(1) Put the belt cleaner release sensor harness and belt cleaner release solenoid harness

through the hole on the paper feed frame.

(2) Put the two harnesses above and T1 PE/edge sensor harness through the PF CR harness

holder and put them out of the hole on the Side frame L.

(3) Hold the PU lift up cam with a Screwdriver or similar and push to the back of the machine .

The section “B” shown in

Fig. 3-183

in the next page can be moved up and down by this

operation, which makes it easy to assemble the lift arm.

Fig. 3-181

PU lift up cam

Side frame L

<Front>

Screwdriver

Содержание DCP-9045CDN












































































































































































































































































































































































































































































































Результаты поиска

Содержание DCP-9045CDN

Отзывы:

Бренды по названию

Популярные бренды

Brother DCP-9045CDN, Руководство по обслуживанию

Результаты поиска

Содержание DCP-9045CDN

Отзывы:

Бренды по названию

Популярные бренды