Brother DCP-9045CDN Скачать руководство пользователя страница 62

Страница: 62 / 491

Confidential

1-43

3.4 Dirt on Paper

User Check

Check if the paper is loaded into the paper tray correctly.

- Turn over the stack of paper in the paper tray, or try rotating the paper 180° in the paper tray.

Step

Cause

Check

Result

Remedy

Is there dirt around the
entrance of the fuser unit?

Yes

Clean the entrance of the
fuser unit.

Fuser unit dirty

Is the pressure roller
ASSY dirty?

Yes

Clean the pressure roller
ASSY.

Dirt on belt unit
electrode

Is the electrode of the belt
unit dirty?

Yes

Clean the electrode of the
main body and the belt
unit.

Dirt on waste
toner box
electrode

Is the electrode of the
waste toner box dirty?

Yes

Clean the electrode of the
main body and the waste
toner box.

Belt unit dirty

Does dirt on the paper
disappear after replacing
the belt unit with a new
one?

Yes

Replace the belt unit.

Toner leak from
the waste toner
box

Is the waste toner box full
of toner?

Yes

Replace the waste toner
box. Check the near/full
sensor ASSY. Or, replace
the main PCB ASSY.

3.5 Wrinkles

User Check

Check if the paper is loaded into the paper tray correctly.

- Turn over the stack of paper in the paper tray, or try rotating the paper 180° in the paper tray.

Step

Cause

Check

Result

Remedy

Fuser unit failure

Do wrinkles on the paper
disappear after replacing
the fuser unit with a new
one?

Yes

Replace the fuser unit.

Содержание DCP-9045CDN












































































































































































































































































































































































































































































































Результаты поиска

Содержание DCP-9045CDN

Отзывы:

Бренды по названию

Популярные бренды

Brother DCP-9045CDN, Руководство по обслуживанию

Результаты поиска

Содержание DCP-9045CDN

Отзывы:

Бренды по названию

Популярные бренды