Brother 888-P30 Скачать руководство пользователя

Страница: 11 / 60

Names of Machine Parts

GE
T

G RE

■

Main parts

Bobbin winding thread guide and pretension disk
(page 18)

Thread guide (page 18)

Spool cap (page 18)

Spool pin (page 18)

Bobbin winder (page 17)

LCD (liquid crystal display) (page 13)

Operation panel (page 10)

Operation buttons (page 10)

Embroidery unit (page 29)

Thread cutter (page 22)

Needle threader lever (page 23)

Thread tension dial (page 35)

Handwheel

Turn the handwheel toward you (counterclockwise) to raise and
lower the needle.

Thread guide cover (page 18)

Handle

Carry the machine by its handle when transporting.

Presser foot lever

Raise and lower the presser foot lever to raise and lower the
presser foot.

Main power switch (page 12)

Power supply jack (page 12)

Air vent

The air vent allows the air surrounding the motor to circulate.
Do not cover the air vent while the machine is being used.

USB port (for a USB flash drive) (page 43)

■

Needle and presser foot section

Needle bar thread guide (page 22)

Needle plate

Needle plate cover (page 20)

Bobbin cover/bobbin case (page 19, page 46)

Embroidery foot (page 33, page 47)

The embroidery foot helps control fabric flexibility for better
stitch consistency.

Embroidery foot screw (page 47)

Use the embroidery foot screw to hold the embroidery foot in
place.

■

Embroidery unit

Embroidery carriage frame holder (page 29)

Embroidery unit connection (page 25)

Carriage (page 25)

Release button (page 26)

Chapter

GETTING READY

Note

• Be sure to install the latest software.

Refer to “Updating Your Machine’s Software” on
page 56.

Names of Machine Parts

IMPORTANT

• Do not insert anything other than a USB flash

drive into the USB port. Anything else may
damage the machine.

Содержание 888-P30





























































Результаты поиска

Содержание 888-P30

Отзывы:

Похожие инструкции для 888-P30

Бренды по названию

Популярные бренды

Brother 888-P30, Руководство по эксплуатации

Результаты поиска

Содержание 888-P30

Отзывы:

Похожие инструкции для 888-P30

Бренды по названию

Популярные бренды