Brother 888-P30 Скачать руководство пользователя | Manualshive

Страница: 5 / 60

background image

3

FOR USERS IN THE UK,

EIRE, MALTA AND

CYPRUS ONLY

IMPORTANT

• In the event of replacing the plug fuse, use a fuse

approved by ASTA to BS 1362, i.e. carrying the

mark, rating as marked on plug.

• Always replace the fuse cover. Never use plugs with

the fuse cover omitted.

• If the available electrical outlet is not suitable for the

plug supplied with this equipment, you should
contact your authorized Brother dealer to obtain the
correct lead.

Federal Communications

Commission (FCC)

Supplier’s Declaration of

Conformity (For U.S.A.

Only)

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.

This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is
connected.

• Consult the authorized Brother dealer or an

experienced radio/TV technician for help.

• This transmitter must not be co-located or operated

in conjunction with any other antenna or
transmitter.

Important

Changes or modifications not expressly approved by
Brother Industries, Ltd. could void the user’s authority
to operate the equipment.

This equipment complies with FCC/IC radiation
exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF)
Exposure Guidelines and RSS-102 of the IC radio
frequency (RF) Exposure rules. This equipment should
be installed and operated keeping the radiator at least
20cm or more away from person’s body.

Responsible Party:

Brother International Corporation
200 Crossing Boulevard
P.O. Box 6911
Bridgewater, NJ 08807-0911
USA
TEL : (908) 704-1700

declares that the product

Product Name:
Model Number:

Brother Embroidery Machine
PE545

«
...
3
4
5
6
7
...
»

Содержание 888-P30





























































Отзывы:

Нет отзывов

Похожие инструкции для 888-P30

Бренд: Janome Страницы: 2

Бренд: Janome Страницы: 75

Бренд: Janome Страницы: 40

Бренд: Janome Страницы: 45

Бренд: Janome Страницы: 51

Бренд: Janome Страницы: 2

MEMORY CRAFT 9700

Бренд: Janome Страницы: 110

Memory Craft 3000

Бренд: Janome Страницы: 42

Memory Craft 10001

Бренд: Janome Страницы: 181

Бренд: Janome Страницы: 41

Бренд: Janome Страницы: 32

Бренд: Singer Страницы: 29

Бренд: MasterCraft Страницы: 6

Бренд: Ricoh Страницы: 109

Бренд: Unicorn Страницы: 18

Easy Melt Air 1G

Бренд: Ultraflex Страницы: 22

Citymaster 1250

Бренд: HAKO Страницы: 40

Бренд: Chikon Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды