Brother 888-P30 Скачать руководство пользователя

Страница: 53 / 60

Troubleshooting

PPE

Fabric is snagged or caught on something.
• Stop the machine and place the fabric so that it

does not get caught or snagged.

–

The carriage was moved while the embroidery
frame was being removed or attached during
embroidery.
• If the carriage is moved during the process, the

pattern may be misaligned. Be careful when
removing or attaching the embroidery frame.

Stabilizer is incorrectly attached, for example, it is
smaller than the embroidery frame.

Embroidery pattern does not embroider in a particular
position.

Fabric is not positioned with the proper position in
the embroidery frame.
• Use the embroidery sheet.

Loops appear on the surface of the fabric when
embroidering.

The thread tension is incorrectly set.

Embroidery bobbin thread intended for use with
this machine is not being used.

Symptom, Cause/solution

Reference

Содержание 888-P30





























































Результаты поиска

Содержание 888-P30

Отзывы:

Похожие инструкции для 888-P30

Бренды по названию

Популярные бренды

Brother 888-P30, Руководство по эксплуатации

Результаты поиска

Содержание 888-P30

Отзывы:

Похожие инструкции для 888-P30

Бренды по названию

Популярные бренды