BRONKHORST mini CORI-FLOW ML120 Скачать руководство пользователя страница 51

Страница: 51 / 65

Bronkhorst®

Instruction Manual mini CORI-FLOW ML120

9.17.097G

If the 9-pin D-sub (side) connector of the instrument is configured for RS485 communication (FLOW-BUS/Modbus), it will

not respond when connected to an RS232 configuration. In that case, use the power-up functionality of the

multifunctional

switch

to switch to configuration mode and enable RS232 communication.

After configuring the required parameters, remember to return the instrument to the original communication mode.

5.3.1

Dosing method

With

CORI-FILL™

, batch dosing can be done based on mass

or volume flow. By choosing the required unit type, the

batch counter is automatically configured to use similar

units.

In FlowPlot, the fluid settings for determining the dosing

method are located on the

Basic

tab of the

Instrument Settings

function (see image to the right).

For volume flow based dosing, the instrument needs the

fluid density to calculate the volume and batch size from the

mass flow measured by the instrument. The instrument

supports different types of volume measurement.

Depending on the specific type selected, the actual

(measured by the instrument) or theoretical fluid density is

used.

For liquid dosing, FlowPlot supports Mass Flow and Volume

Flow; for gas, Mass Flow, Normal Volume Flow or Standard

Volume Flow can be selected.

With

Mass Flow

, the instrument does not need extra

information to calculate the batch size:

When

Volume Flow

Normal Volume Flow

Standard

Volume Flow

is selected, the instrument needs the

theoretical fluid density to calculate the batch volume.

Because Normal Volume Flow and Standard Volume Flow

are typical gas flow units, for these unit types the fluid

density at normal (0 °C, 1 atm) or standard conditions (20 °C,

1 atm) respectively is needed.

With

Actual Volume Flow

, the actual fluid density, measured

by the instrument, is used to calculate the batch volume:

Because the mini CORI-FLOW ML120 measures mass flow, this is also the preferred dosing method. For volume based

capacity units, the fluid density is needed to calculate the batch size (see the descriptions below), which is less accurate (and

slower) than using the measured mass flow directly.

Содержание mini CORI-FLOW ML120


































































Результаты поиска

Содержание mini CORI-FLOW ML120

Отзывы:

Похожие инструкции для mini CORI-FLOW ML120

Бренды по названию

Популярные бренды

BRONKHORST mini CORI-FLOW ML120, Инструкция по эксплуатации

Результаты поиска

Содержание mini CORI-FLOW ML120

Отзывы:

Похожие инструкции для mini CORI-FLOW ML120

Бренды по названию

Популярные бренды