BRONKHORST ES-FLOW ES Series Скачать руководство пользователя

Страница: 45 / 55

Bronkhorst®

Instruction Manual ES-FLOW™

9.17.145E

Serial Number

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char[20]



113/3

0xF118…0xF11F/ 61721…61728

Instrument serial number for identification.

BHT Model Number

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char[35]



113/2

0xF110…0xF117/ 61713…61720

This parameter shows the Bronkhorst® instrument model type information.

Firmware Version

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char[6]

105

113/5

0xF128…0xF12A/ 61737…61739

Revision number of the firmware

Identification Number

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char



0…255

175

113/12

0x0E2C/3629

Bronkhorst® (digital) device type identification number.

Device Type

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char[6]

113/1

0xF108…0xF10A/ 61705…61707

Device type information string; this parameter contains an abbreviation referring to the identification number.

3.4.9

Special parameters

Init Reset

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

82/64

0/10

0x000A/11

Init Reset

is used to unlock secured parameters (marked with a



symbol) for writing. It supports the following values:

Value

Description

unlocked, secured parameters can be read and written to

locked, secured parameters are read-only

At power-up,

Init Reset

is always set to ‘Locked’ (value 82).

Reset

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

0…7

114

115/8

0x0E68/3689

This parameter is used to reset the program, counter, totalizer or alarms.

Содержание ES-FLOW ES Series
























































Результаты поиска

Содержание ES-FLOW ES Series

Отзывы:

Похожие инструкции для ES-FLOW ES Series

Бренды по названию

Популярные бренды

BRONKHORST ES-FLOW ES Series, Инструкция по эксплуатации

Результаты поиска

Содержание ES-FLOW ES Series

Отзывы:

Похожие инструкции для ES-FLOW ES Series

Бренды по названию

Популярные бренды