BRONKHORST ES-FLOW ES Series Скачать руководство пользователя

Страница: 11 / 55

Bronkhorst®

Instruction Manual ES-FLOW™

9.17.145E

Code

Description

D9E

Digital frequency output, measure

Measurement value is translated to a frequency within given frequency range.

The default frequency range to represent 0…100% flow is 0…10000 Hz. Any other frequency range must be

specified on order.

F9B

Digital pulse output, batch counter

Pin 5 is pulled down to 0Vdc when a given batch size is reached (during a given pulse length).

By default, a pulse is given at each 1x the

Counter unit

batch value, with a pulse length of 1 second. For

instance, when

Counter unit

is set to 'ln', a pulse is given each time 1 ln has passed through the instrument.

An alternative pulse length must be specified on order.

Provide a pull-up resistor of 5…10 kOhm to create 15…24 Vdc at pin 5 (according to the applicable hook-up

diagram).

I3C

Digital input, controller mode valve close

Valve closes when pin 5 is connected to 0 Vdc.

This option switches between the default

Control mode

and mode ‘Valve Close’ (value 3). When the default

Control mode

is digital, the default value is 0 (bus/RS-232), when the default

Control mode

is analog, the

default value is 1 (Analog input).

I8C

Digital input, controller mode valve purge

Valve is fully opened when pin 5 is connected to 0 Vdc.

This option switches between the default

Control mode

and mode ‘Valve Fully Open’ (value 8). When the

default

Control mode

is digital, the default value is 0 (bus/RS-232), when the default

Control mode

is analog,

the default value is 1 (Analog input).

I1R

Digital input, reset counter

The counter resets when pin 5 is connected to 0 Vdc.

I2R

Digital input, reset alarm

The alarm resets when pin 5 is connected to 0 Vdc.

*) Notes regarding controller options:

A controller output option (A1V, B1V or B2V) can only be installed in combination with controller mode A or D

(controller enabled, see model key).

If the controller is enabled, the M8 connector can always be used to control a Bronkhorst® valve (through pin 3).

Although it is theoretically possible to have 3 controller options installed, no more than 1 signal should be used at any

time.

Содержание ES-FLOW ES Series
























































Результаты поиска

Содержание ES-FLOW ES Series

Отзывы:

Похожие инструкции для ES-FLOW ES Series

Бренды по названию

Популярные бренды

BRONKHORST ES-FLOW ES Series, Инструкция по эксплуатации

Результаты поиска

Содержание ES-FLOW ES Series

Отзывы:

Похожие инструкции для ES-FLOW ES Series

Бренды по названию

Популярные бренды