10
ES-2200T Card Installation
1.
Remove the carrier plates from the backs of the cards. Save the screws to mount the cards in the chassis.
2.
With the power off, remove the top cover of the chassis.
3.
If the card to be installed in the unit 1 position is a Personal V-Scope, place DIP Switch 1 in the DOWN position,
and all others UP. For all other card types, place DIP Switch 2 on the card intended for unit 1 in the DOWN
position and all others UP.
4.
If a Personal V-Scope is to be installed in the Unit 2 position, place DIP Switch 1 on the V-Scope in the DOWN
position, and all others UP. If any other type of card is intended for the unit 2 position, place DIP Switches 2, 3, 4,
5, 6 and 7 on that card in the DOWN position and all others UP.
5.
On the ES-2200 front panel, place DIP Switches 1, 2, 3, 4 and 5 in the UP position. DIP Switches 6, 7 and 8 are
placed in the following positions, depending on what combination of cards you are installing:
Unit 1 Unit 2 Switch 6 Switch 7 Switch 8
TBC
TBC
DOWN
DOWN
DOWN
TBC
V-Scope
DOWN
DOWN
UP
TBC
Routing Switcher
DOWN
UP
DOWN
TBC
8-Bit MicroSYNC
DOWN
UP
UP
8-Bit MicroSYNC
TBC
UP
DOWN
DOWN
8-Bit MicroSYNC
V-Scope
UP
DOWN
UP
V-Scope
V-Scope
UP
UP
DOWN
Routing Switcher
Routing Switcher
UP
UP
UP
If you are installing a single card in the ES-2200T, it should be placed in the unit 1 position unless it is a V-Scope.
The Personal V-Scope should always be in the Unit 2 position except if the ES-2200T chassis is intended to hold
two Personal V-Scopes. If a single V-Scope is to be the only card in the ES-2200T chassis, DIP Switch settings
option #7 (UP, UP, DOWN) should be chosen.
If there is no card intended for the unit 2 position, select a DIP Switch setting to indicate what is in the Unit 1
position. For example, if you put a lone MicroSYNC card in the Unit 1 position, the DIP Switches could be set to
UP, DOWN, DOWN (MicroSYNC and TBC) or UP, DOWN, UP (MicroSYNC and V-Scope). If a VDA is
intended for the unit 2 position, set the DIP Switches as if the position was empty.
6.
Install the 3 wire RS-232 cable for unit 1 (figure 2-1) to the 3 pin header labeled INPUT at the top of the first card
near the BNC connectors near the fan.
7.
Press the power supply's edge connector for unit 1 onto the first card as far as it will go.
8.
Mount the first card in the unit 1 position using the five screws provided and install the supplied hardware for the
rear panel support bracket.
9.
Install the 3 wire RS-232 cable for unit 2 (figure 2-1) to the 3 pin header labeled INPUT at the top of the second
card near the BNC connectors.
10.
Press the power supply's edge connector for unit 2 onto the second card as far as it will go.
11.
Mount the second card in the unit 2 position using the five screws provided and install the supplied hardware for
the rear panel support bracket and install the top cover.
NOTE:
While baud rates the individual cards installed in the ES-2200T chassis are capable of being set to DOWN
(9600 BPS) or UP (31,250 BPS), the ES-2200T chassis defaults to 9600 BPS. Therefore, DIP Switch 2 should always
be in the DOWN position on cards that are to be installed in the ES-2200T Expansion System.
Содержание DPS ES-2200
Страница 1: ...ES 2200 Dual Channel Expansion System Operator s Manual...
Страница 56: ...55 Appendices...
