Brita BPF89CATCB100TOC Скачать руководство пользователя страница 48

48

48

3) LIMITED TEN YEAR WARRANTY FOR  MINERAL TANKS AND    

  

BRINE TANKS (SILVER SYSTEM AND NRV):

Protect Plus Pro, LLC will provide a replacement mineral tank or brine tank to any 

approved  dealer that purchased the new water conditioner assembled unit from 

Protect Plus Pro, LLC and whose client is  in possession of a tank that fails within 120 

months, provided that the water conditioner is at all times operated in accordance with 

specifications, contained within the owner’s manual, and not subject to freezing or 

negative pressure vacuum.

Limitations To Limited Warranty: Damage to any part of this water conditioner  as a 

result of misuse, misapplication, neglect, alteration, accident, installation or operation 

contrary to our printed instructions, contained within the owner’s manual, damage to ion 

exchange resin and seals caused by chlorine / chloramines in the water supply, or damage 

caused  by any force of nature is not covered in this warranty. DAMAGE TO PISTONS, 

SEALS, AND OR SPACERS WITHIN THE CONTROL VALVE ARE NOT COVERED UNDER THIS 

WARRANTY, IF THESE PARTS ARE EXPOSED TO HARSH ENVIRONMENTAL CONDITIONS, 

SUCH AS HIGH LEVELS OF IRON, MANGANESE, SULPHUR, AND SEDIMENT.  We will 

repair or replace defective parts if our warranty department determines it to be defective 

under the terms of this warranty.   Protect Plus Pro, LLC assumes no responsibility for 

consequential damage, labor or expense incurred as a result of a defect or failure. Media 

and Resin coverage is limited to the warranty provided by the original manufacturer.  For a 

copy of this warranty, please contact Protect Plus Pro, LLC.  

B)

 

LIMITED WARRANTY ON COMPONENT PARTS NOT     

    PURCHASES AS PART OF A NEW WATER CONDITIONER  

    ASSEMBLED UNIT

For Component parts not sold as a part of a new water conditioner assembled unit system 

are warranted to do the work for which they are intended where properly installed and 

operated.  The new water conditioner assembled unit consists of a control valve, pressure 

tank, and brine tank sold as a complete, assembled unit.  For component parts not sold 

as a new water conditioner assembled unit, Protect Plus Pro, LLC provides the following 

limited warranty on the component parts: 

 

1) FIBERGLASS TANKS- 

Protect Plus Pro, LLC will provide a replacement fiberglass  

    tank to any  dealer whose client is  in possession of a fiberglass tank that fails within  

    120 months, provided that the water conditioner is at all times operated in accordance  

    with specifications, contained within the owner’s manual, and not subject to freezing or  

    negative pressure vacuum;

 

2) CONTROL VALVE AND ASSOCIATED ELECTRONICS-

 Protect Plus Pro, LLC  

    will replace the control valve of any new water conditioner assembled unit which fails  

    within 60 months from date of purchase by the dealer or installation by the dealer;

 

3) BRINE TANKS AND RELATED ASSEMBLIES- 

Protect Plus Pro, LLC will    

    provide a replacement brine tank to any  dealer whose client is in possession of  

 

    a brine tank that fails within 60 months, provided that the water conditioner is at  

 

    all times operated in accordance with specifications, contained within the owner’s    

    manual, and not subject to freezing or negative pressure vacuum; 

 

4) MEDIA AND RESIN- 

Media and Resin coverage is limited to the warranty provided  

    by the original manufacturer.  For a copy of this warranty, please contact Protect Plus  

    Pro, LLC; and

5)

 DAMAGE TO PISTONS, SEALS, AND OR SPACERS WITHIN THE CONTROL VALVE  

ARE NOT COVERED UNDER THIS WARRANTY, IF THESE PARTS ARE EXPOSED TO HARSH 

ENVIRONMENTAL CONDITIONS, SUCH AS HIGH LEVELS OF IRON, MANGANESE, SULPHUR, 

AND SEDIMENT.

Protect Plus Pro, LLC only provides a limited warranty for this product to its approved 

dealers.  Protect Plus Pro, LLC does not provide any warranty to any consumer purchaser or 

household purchaser of this product.  The consumer purchaser or household purchaser 

should consult the dealer they purchased this product from to determine the warranty, if any, 

provided by the dealer.   

LIMITED

 W

ARRANT

Y

Содержание BPF89CATCB100TOC

















































Отзывы: