© BriskHeat
®
Corporation. All rights reserved
.
3
SRL5, SR, SRV, FGH, and SXH
Composite Curing Blankets
IMPORTANT SAFETY INSTRUCTIONS
Never operate heater without a temperature control
device. Failure to use such a device may result in
process damage or heater failure.
Inspect heater before use (see page 9)
Never operate a heater without an appropriate heat
sink (device being heated is considered to be a heat
sink).
Never expose the heater to temperatures above the
rated exposure temperature.
Fluid should not be allowed to come in contact with the
heater.
Never lift or pull the heater by its power cord or lead
wire.
Never cut, punch holes in or otherwise modify heater.
Do not use tools such as pliers or vice grips to pull or
tighten the heater.
Failure to observe these warnings may result in personal injury
or damage to the heater.
CAUTION
WARNING
CAUTION
Immediate hazards which
WILL
result in severe personal injury or
death.
Hazards or unsafe practices that
COULD
result in severe personal
injury or death.
Hazards or unsafe practices that
COULD
result in minor personal
injury or property damage.
DANGER
Do not immerse heater in liquid.
Keep volatile or combustible material away from
heater when in use.
Use heater only in approved locations
Keep sharp metal objects away from heater.
Never handle the heater while it is in operation.
Always disconnect the heater from power source and
allow to cool prior to removing from the surface.
Do not use in the presence of flammable or
combustible materials, fire or explosion may result.
The heater contains components which may ignite
such materials
Do not modify this product. Modification will void
warranty.
Failure to observe these warnings may result in electric shock,
risk of fire, and personal injury.
End User Must Comply to the Following:
Only qualified personnel are allowed to connect the
electrical wiring.
Disconnect all supply power at the source before
making any heating cable power input connections.
All electrical wiring must follow local electrical codes.
The person who performs the final installation / wiring
must be qualified for this work.
The end-user is responsible for providing a suitable
disconnecting device.
The end-user is responsible for providing suitable
electrical protection device. It is highly recommended
that a ground fault circuit breaker be used.
Failure to observe these warnings may result in personal injury
or damage to the product and/or property.
WARNING
A person who has not read and understood all operating
Instructions is not qualified to operate this product.
DANGER
DANGER
Your Heating Blanket is designed to provide a long and efficient
service life. Overheating , contamination and misuse will greatly
reduce the life of the heater, Your heater should only be used in
dry, non-hazardous areas. Only use the heater on the surface it
is designed to heat.
OPERATION
SAFETY ALERT SYMBOL
The symbol above is used to call your attention to instructions
concerning your personal safety. It points out important safety
precautions. It means
“ATTENTION! Become Alert! Your
Personal Safety is involved!”
Read the message that follows
and be alert to the possibility of personal injury or death.
© BriskHeat
®
Corporation. All rights reserved
.
4
SRL5, SR, SRV, FGH, and SXH
Composite Curing Blankets
HEATER CHARACTERISTICS / SPECIFICATIONS
Part Series
SRL5
SR
SRV
FGH
SXH
Max Power Density
(W/in²)
2.5 W/in
2
(63.5 W/mm
2
)
5 W/in
2
(127 W/mm
2
)
5 W/in
2
(127 W/mm
2
)
7 W/in
2
(177 W/mm
2
)
13 W/in
2
(330 W/mm
2
)
Minimum Bend
Radius
3”
(76mm)
1/4”
(6 mm)
3’’ (76 mm) With
Blanket Seal
1” (25.4mm)
.25’’ (6 mm)
Without
Blanket Seal
Max Exposure
Temperature
450°F (232°C) 450°F (232°C) 450°F (232°C) 450°F (232°C) 450°F (232°C)
Max Humidity
95%
95%
95%
95%
95%
Ingress Protection
IP56
IP56
IP56
IP4X
IP4X
Moisture and
Chemical Resistant
✓
✓
✓
1” (25.4 mm)
