brewer Flex 5700 Скачать руководство пользователя страница 2

Brewer

FLEX

Access

Exam Table

Printed in USA © 2015 

Document # 2102861 RevA

Service

If you require assistance with the installation or operation 

of your Brewer table, call the Brewer Customer Service 

Department at 

(1-888-Brewer1)

. Our trained staff will 

attempt to assist you in correcting the problem directly 

over the phone. If service is required, a factory authorized 

technician will be sent to your location.

Please fill in the following information for use when calling 

the Brewer Company or your distributor with questions 

regarding your unit. 

Date of Purchase

Serial Number

Model Number

Authorized  

Dealer Name

Dealer  

Phone Number

Dealer Address

IMPORTANT INFORMATION

General

Read and understand all operating instructions, safety 

information, and maintenance requirements contained in 

this manual prior to operating the table.  Become familiar 

with all of the table functions before using it with a patient.

The Brewer Flex Access Exam Table Models 5700 

and 5800 Series are designed to provide positioning 

and support of patients during general examinations 

conducted by qualified medical professionals. The Brewer 

Flex Access Exam Table is primarily used in examination 

rooms for general examinations and minor procedures. 

The wide variety of positions provided by one or two 

powered motions, and slide-out leg support create a safe 

and convenient patient positioning table for use in the 

doctor’s office.

The table is easily adjusted to a wide variety of positions 

using the convenient foot control provided with the table.  

The table height can be adjusted from 18” to 37”.  The 

table seating surface on models 5701 and 5801 can be 

moved from the normal horizontal position to an angle of 

5°.  The backrest can be adjusted from a flat lying down 

position, to an 80° angle for seating.

In addition to the electronically controlled positions noted 

above, several manual adjustments are available: 
Standard Features
•    The SafeGlide™ leg support can be extended up to 

21” for the patient prone position.

•    A removable treatment pan is built-in underneath the 

leg support pad for use during examinations.

•    A storage drawer at the front of the table may be used 

for supplies.

Optional Features
•    Stirrups - may be manually extended through infinite 

positions and four lateral positions.

•    Grab bars - attached to each side of the table may be 

rotated out of position or removed for improved ac-

cess to the patient.

•    Pass through work surface - stored under the seat, 

may be pulled out from either side of the table.

Содержание Flex 5700
























Отзывы: