background image

 

STOVE WILL NOT FEED PELLETS, BUT FUEL FEED LIGHT COMES ON AS DESIGNED 

Possible Causes: 

Possible Remedies: 

 
1. 

Fuse on control board blew 

 

 
Remove the control board.  On the back there is one fuse. If it 
appears to be bad, replace it with a 5 Amp 250 Volt fuse.  Plug the 
stove back in and try to run the unit. 
 

 
2. 

High limit switch has tripped or is defective 

 

 
Wait for the stove to cool for about 30 - 45 minutes. It should now 
function normally. If not use the owner’s manual to locate the high 
limit thermodisk. To test if the thermodisk is bad, you can bypass it 
as described previously for the POF thermodisk. 
 

 
3. 

Bad auger motor 

 

 
Remove the auger motor from the auger shaft and try to run the unit.  
If the motor will turn, the shaft is jammed on something.  If the motor 
will not turn, the motor is bad. 
 

 
4. 

Auger jam 

 

 
Start by emptying the hopper.  Then remove the auger motor by 
removing the auger pin. Remove the auger shaft inspection plate in 
the hopper so that you can see the auger shaft.  Gently lift the auger 
shaft straight up so that the end of the auger shaft comes up out of 
the bottom auger bushing.  Next, remove the two nuts that hold the 
top auger biscuit in.  Then rotate the bottom end of the auger shaft 
up towards you until you can lift the shaft out of the stove.  After you 
have removed the shaft, inspect it for bent flights, burrs, or broken 
welds.  Remove any foreign material that might have caused the 
jam.  Also, check the auger tube for signs of damage such as burrs, 
rough spots, or grooves cut into the metal that could have caused a 
jam. 
 

 
5. 

Loose wire or connector 

 

 
Check all wires and connectors that connector to the auger motor, 
high limit switch, and the Molex connector. 
 

 
6. 

Bad control board 

 

 
If the F2 fuse is good, the wires and connectors check out good, and 
the high limit switch did not trip, test for power going to the auger 
motor.  If there is not a full current going to the auger motor when 
the fuel feed light is on, you have a bad control board. 
 

 

TROUBLESHOOTING GUIDE 

22 

Содержание Big E SP1000PB




























Отзывы: