background image

Page 22

WA

RNING

Lift Operation Safety

Keep operator and bystanders clear of area in which the lift operates.

Lift attendant must observe passenger at all times during lift operation.

Ensure adequate lighting exists in the lift operating area.

Whenever a wheelchair passenger (or standee) is on the platform, the:

• Passenger must be positioned fully inside yellow boundaries facing outward.

• Wheelchair brakes must be locked

• Bridge plate and roll stop must be up (vertical)

• Roll Stop latch must be fully engaged

• Passenger should grip both handrails (if able).

Wheelchair lift attendants should be instructed on any special needs and/or procedures  

required for safe transport of wheelchair passengers.

Load and unload clear of vehicular traffic.

Do not attempt to load or unload a passenger in a wheelchair or other apparatus that 

does not fit on the platform area.

The lift attendant shall not ride on the platform with the passenger.  The lift is intended  

for use by a single passenger.

Do not overload or abuse.  The load rating applies to both the raising and lowering 

functions.

Use caution when operating this equipment out of doors during electrical storms or 

similar electrical phenomena.

Use caution when operating this equipment in severe weather or environmental 

conditions (fog, rain, snow, ice, dust, etc.) 

Discontinue lift use immediately if any lift or vehicle interlock does not operate properly.

Do not operate or board the lift if you or your lift operator are intoxicated.

WA

RNING

WA

RNING

WA

RNING

WA

RNING

WA

RNING

WA

RNING

WA

RNING

WA

RNING

WA

RNING

WA

RNING

WA

RNING

Lift Operation Safety Precautions 

Read manual and supplement(s) before operating lift.  

Read and become familiar with all safety precautions, 

operation notes and details, operating instructions and 

manual operating instructions before operating the lift.  

Load and unload on level surface only.

Engage vehicle parking brake before operating lift.

Provide adequate clearance outside the vehicle to accom-

modate the lift before opening lift door(s) or operating lift.

Inspect lift before operation.  Do not operate lift if you 

suspect lift damage, wear or any abnormal condition.

Do not use as a link bridge.

WA

RNING

WA

RNING

WA

RNING

WA

RNING

If the lift operating 

instructions, manual 

operating instructions 

and/or lift operation 

safety precautions are 

not fully understood, 

contact The Braun 

Corporation immedi-

ately.  Failure to do so 

may result in serious 

bodily injury and/or 

property damage.

WA

RNING

WA

RNING

WA

RNING

WA

RNING

Содержание Millennium 2 L917IB3751RP-2













































Отзывы: