manualshive.com logo in svg

Braun Corporation Millennium 2 L917IB3751RP-2, Руководство пользователя

Поделиться
Скачать
Braun Corporation Millennium 2 L917IB3751RP-2 Скачать руководство пользователя страница 28

Page 26

L

K

Lift Operating Instructions

F

E

Notice:  Roll stop must be 

fully unfolded (ramp position) 

until the entire wheelchair (or 

standee) has crossed the roll 

stop.  See Photos E and F.

H

g

TO LOAD PASSEngER:

1. Read Notices below!  Load 

passenger onto platform and 

lock wheelchair brakes.  See  

Photo G.  

Notice:  Roll stop must be 

fully unfolded (ramp position) 

until the entire wheelchair (or 

standee) has crossed the roll 

stop.  See Photos E and F.

Notice:  Passenger must be 

positioned fully inside yellow 

boundaries.

J

I

2. Press    UP switch (Photo H) 

to fold roll stop UP fully (verti-

cal - see Photo I), and raise 

the platform to floor level.  

See Photo J.  Release switch.  

3. Unlock wheelchair brakes 

and unload passenger from 

platform.

TO FOLD PLATFORM:

Press      FOLD (In) switch un-

til platform stops (fully folded).  

See Photos K and L.  Release 

switch

CLOSE DOOR(S)

Содержание Millennium 2 L917IB3751RP-2













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды