Braun Corporation Millennium 2 L917IB3751RP-2 Скачать руководство пользователя страница 18

Страница: 18 / 44

Page 16

Lift Installation

Platform Angle Adjustment

Figure B

Lowering Sequence Requirements

1. The outboard end (toe)

of the platform must contact

the ground first to ensure the

spring-loaded outer barrier

unfolds fully. See Figure B.

2. The inboard end (heel) of

the platform must lower fully

(vertical arms must contact

ground when fully lowered).

See Figure B.

The angle of the platform at

ground level directly affects

the angle of the platform when

positioned at floor level.

Raise the platform to floor

level. Note the angle of the

platform.

The platform at floor level

should have a slight upward

angle as shown in Figure C.

Adjust platform angle as de-

tailed below.

(Heel) Inboard

Outboard (Toe)

Rear

Front

Outboard

(passenger's side)

Inboard

(driver's side)

“Arrows/Direction

(of vehicle)

Heel

Ground Level

Barrier must

unfold fully.

Platform heel

must lower fully.

Barrier

Floor level

Wedges (option)

Figure C

Adjustment Procedure:

Platform angle adjustment

Allen screws are provided on

each side of the platform (see

photo at right).

Turn adjustment screws clock-

wise to raise the outboard end

of the platform. Turn adjust-

ment screws counterclockwise

to lower the outboard end of

the platform.

Both adjustment screws must

be adjusted equally.

Platform Stop Blocks: When

adjusting platform angle, en-

sure both stop blocks are mak-

ing full contact with the vertical

arms (see photo at right).

Floor Level Adjustment:

Following platform angle

adjustment, set floor level posi

tioning as detailed in Tower

Microswitch Adjustment.

Check platform angle again

after performing Tower Micro-

switch Adjustment procedures.

Adjustment Screw

Stop blocks must

make full contact.

Stop

Block

Vertical

Arm

36514

Содержание Millennium 2 L917IB3751RP-2













































Результаты поиска

Содержание Millennium 2 L917IB3751RP-2

Отзывы:

Бренды по названию

Популярные бренды

Braun Corporation Millennium 2 L917IB3751RP-2, Руководство пользователя

Результаты поиска

Содержание Millennium 2 L917IB3751RP-2

Отзывы:

Бренды по названию

Популярные бренды