background image

 

22

Maintenance continued-

 

 

6.  At least once a year, check the combination temperature and pressure 

relief valve to insure that the valve has not become encrusted with lime.  
Lift the lever at the lever at the top of the valve several times until the 
valve seats properly without leaking and operates freely. 

 

 

 

7.  Monthly drain off a gallon of water to remove silt and sediment.        

 

8.  If the combination temperature and pressure relief valve on the appliance 

discharges periodically, this may be due to thermal expansion in a closed 
water supply system.  Contact the water supplier or local plumbing 
inspector on how to correct this situation.  Do not plug the combination 
temperature and pressure relief valve outlet. 

 

9.  A combination sacrificial anode rod/hot water outlet nipple has been 

installed to extend tank life.  The anode rod should be inspected 
periodically (every 2 years) and replaced when necessary to prolong tank 
life.  Water conditions in your area will influence the time interval for 
inspection and replacement of the anode rod.  Contact the plumbing 
professional who installed the water heater or the manufacturer listed on 
the rating plate for anode replacement information. The use of a water 
softener may increase the speed of anode consumption. More frequent 
inspection of the anode is needed when using softened (or phosphate 
treated) water. 
 

10.  The vent system must be inspected at least once a year to ensure against 

leakage of exhaust products. 

 

WARNING 

  Do not operate water heater with jumpered, altered, loosely 

tightened or absent controls and/or components. 

  Do not operate water heater with replacement controls and/or 

components, which are not exact duplicates or original equipment. 

  Thoroughly inspect and replace, (as needed) burner inner door 

gasket and/or sight window gasket any time burner inner door is 
removed or disturbed. 

   Replace water heater if involved in flammable vapors incident.

 

 

WARNING 

When lifting lever of the combination temperature and pressure relief 
valve, hot water will be released under pressure.  Be careful that any 
released water does not result in bodily injury or property damage.

 

WARNING!

  THIS WATER MAY BE HOT.

 

Содержание GAS-FIRED WATER HEATER





























Отзывы: