Bradford White GAS-FIRED WATER HEATER, Инструкция по установке и эксплуатации

Страница: 18 / 28

18
Lighting and Shutdown Instructions
not open the inner door and attempt to light the pilot by hand.
any gas control which has been under water.
service technician to inspect the appliance and to replace any part of the control system and
D. Do not use this appliance if any part has been under water. Immediately call a qualified
attempted repair may result in a fire or explosion.
not push in or turn by hand, don't try to repair it, call a qualified service technician. Force or
C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will
* If you cannot reach your gas supplier, call the fire department.
* Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
* Do not touch any electric switch; do not use any phone in your building.
* Do not try to light any appliance.
WHAT TO DO IF YOU SMELL GAS.
to the floor because some gas is heavier than air and will settle on the floor.
B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next
instructions.
A. This appliance has a pilot which is lit by a piezo-electric spark gas ignition system. Do
GAS CONTROL
KNOB SHOWN IN
"OFF" POSITION
1. STOP! Read the safety information
above on this label.
2. Set the thermostat to lowest setting.
3. Rotate and if applicable partially depress gas
control knob clockwise to "OFF" position.
NOTE: On exhibit B, knob cannot be
turned from "PILOT" to "OFF" unless knob is
depressed slightly. Do not force.
4. Wait five (5) minutes to clear out any gas.
safety information above on this label.
If you don't smell gas, go to the next step.
Then smell for gas, including near the floor.
If you smell gas, STOP! Follow "B" in the
7. Look into sight
5. Remove outer
on inner door
igniter
button.
to view pilot.
glass window
6. Locate piezo
9a. FOR EXHIBIT A GAS CONTROLS-
Depress and hold down red pilot set button.
Immediately depress piezo igniter button until you
hold down the pilot set button for about one (1)
minute after the pilot is lit. Release the pilot set
button and it should pop back up. Pilot should
remain lit. If it goes out, repeat steps 3 through 9.
9b. FOR EXHIBIT B GAS CONTROLS-
Depress and hold down gas control knob.
Immediately depress piezo igniter button until you
hold down the knob for about one (1) minute
after the pilot is lit. Release the knob and it
should pop back up. Pilot should remain lit. If it
goes out, repeat steps 3 through 9.
FOR EXHIBIT A & B GAS CONTROLS-
If button or knob does not pop up when
released, stop and immediately call your
service technician or gas supplier.
If the pilot will not stay lit after several tries,
turn the gas control knob to "OFF" and call
your technician or gas supplier.
11. Turn gas control knob
10. Replace outer door.
12. Set thermostat to desired setting.
8. Turn the gas control knob counterclockwise
GAS CONTROL
KNOB SHOWN IN
"OFF" POSITION
EXHIBIT A EXHIBIT B
hear a "click" sound, then release. Continue to
hear a "click" sound, then release. Continue to
1. Set the thermostat dial to lowest possible setting.
2. Rotate and if applicable partially depress gas control knob clockwise to "OFF" position.
causing property damage, personal injury or loss of life.
WARNING: If you do not follow these instructions exactly, a fire or explosion may result
to "PILOT" position.
counterclockwise to "ON" position.
TO TURN OFF GAS TO APPLIANCE
LIGHTING INSTRUCTIONS
TO TURN OFF GAS TO APPLIANCE TO TURN OFF GAS TO APPLIANCE
FOR YOUR SAFETY READ BEFORE LIGHTING
INNER DOOR
SIGHT GLASS
ELECTRODE
PILOT
BURNER
THERM0-
COUPLE
door.