manualshive.com logo in svg

Bosch UHI Series, Руководство по эксплуатации

Поделиться
Скачать
Bosch UHI Series Скачать руководство пользователя страница 30

Final assembly and Sunshield installation

Final assembly

1.

Use the hole plugs provided to plug any unused holes in the rear cap.

2.

Replace the camera and bracket back into the housing.

3.

Slide the camera/lens tray into the slot near the clasp side of the housing. Refer to
Camera/Lens installation, page 17.

4.

Install screws into the appropriate holes.

5.

Close the cover and secure the latches.

6.

Optional tamper-resistant screws are provided with the housing. If desired, secure the
latch using these three screws and the provided tamper-resistant wrench.

Sunshield installation

1.

Loosen the two screws (M4 x 10) on the top of the housing.

2.

Slide the sunshield to the desired position. It has a range of 50 mm (2 in).

3.

Tighten the screws to lock the sunshade into position.

4.

If the sunshield is removed or not installed, plug the two screw holes with the hole plugs
supplied with the housing hardware kit.

8

8.1

8.2

30

en | Final assembly and Sunshield installation

UHI/UHO Series Camera Housing

2014.05 | 4.0 | F.01U.167.418

Operation Manual

Bosch Security Systems, Inc.

Содержание UHI Series





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды