manualshive.com logo in svg

Bosch HPC 410, Инструкция по установке для подрядчиков

Поделиться
Скачать
Bosch HPC 410 Скачать руководство пользователя страница 3

Explanation of symbols and safety instructions

3

HPC 410 – 6721832682 (2021/02)

1

Explanation of symbols and safety instructions

1.1

Explanation of symbols

Warnings

In warnings, signal words at the beginning of a warning are used to 
indicate the type and seriousness of the ensuing risk if measures for 
minimizing danger are not taken.

The following signal words are defined and can be used in this document:

DANGER

DANGER

 indicates that severe or life-threatening personal injury will 

occur.

WARNING

WARNING

 indicates that severe to life-threatening personal injury may 

occur.

CAUTION

CAUTION

 indicates that minor to medium personal injury may occur.

NOTICE

NOTICE

 indicates that material damage may occur.

Important information

The info symbol indicates important information where there is no risk to 
people or property.

1.2

General safety instructions

H

Notice for the target group

These installation instructions are intended for 
plumbers, heating engineers and electricians. All 
instructions must be observed. Failure to comply with 
instructions may result in material damage and 
personal injury, including possible loss of life.
▶ Read the installation instructions (heat source, 

heating controller, etc.) before installation.

▶ Observe the safety instructions and warnings.
▶ Observe national and regional regulations, 

technical rules and guidelines.

H

Determined use

▶ Use the product only to control heating systems.
Any other use is considered inappropriate. We take no 
responsibility for damage caused through incorrect 
use.

Содержание HPC 410

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды