Bosch FWI-270 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 54

background image

Radio gateway

Safety | en

7

Bosch Sicherheitssysteme GmbH

Operation Manual

2019.10 | 2.0 | F.01U.373.488

CAUTION

Noncompliance with the following safety regulations
Risk of injury to persons and damage to property
Compliance with the following regulations is required.

Specialist electrical engineering knowledge is required for
installation.
Only an expert is permitted to carry out installation work.
Incorrect installation can take safety devices out of operation
unbeknown to a layperson.

Mounting, installation, commissioning and maintenance

If you require tools such as a ladder, these must be safe and must be intended for the work in
hand.
When starting the fire control panel ensure that unstable conditions cannot arise.
Ensure that all points listed in the 'Testing the product operability' section below are
observed.
You may only set controls to normal function when the product operability has been
completely tested and the system has been handed over to the customer.

Testing the product operability

Prevent the remote transmission from triggering erroneously.
If testing building installations or activating devices from third-party companies, you must
collaborate with the people appointed.
The activation of fire control installations for test purposes must not cause injury to anyone or
damage to the building installations. The following instructions must be observed:
Use the correct potential for activation; this is generally the potential of the building
installation.
Only check controls up to the interface (relay with blocking option).
Make sure that only the controls to be tested are activated.
Inform people before testing the alarm devices and allow for possible panic responses.
Inform people about any noise or mist which may be produced.
Before testing the remote transmission, inform the corresponding alarm and fault signal
receiving stations.

Modifications to the system design and the products

Modifications to the system and to individual products may lead to faults, malfunctioning and
safety risks. Written confirmation must be obtained from Bosch and the corresponding safety
bodies for modifications or additions.

Modules and spare parts

Components and spare parts must comply with the technical specifications defined by Bosch.
Only use products specified or recommended by Bosch

«
...
5
6
7
8
9
...
»

Содержание FWI-270























































Отзывы:

Нет отзывов

Похожие инструкции для FWI-270

Бренд: AudioCodes Страницы: 5

Бренд: Chipkin Страницы: 30

Бренд: 4G Systems Страницы: 60

Бренд: Cellio Страницы: 9

Бренд: TRBOnet Страницы: 33

Бренд: ABB Страницы: 11

ATEUS EasyGate 501309E

Бренд: 2N Telekomunikace Страницы: 2

Бренд: Mercury Страницы: 5

Бренд: ipf electronic Страницы: 34

Sentry 556 Series

Бренд: Forum Systems Страницы: 21

Бренд: Fortinet Страницы: 13

Бренд: Fortinet Страницы: 23

Бренд: Zhone Страницы: 151

Бренд: UNION Market Страницы: 36

Бренд: Technicolor Страницы: 98

hotspot gateway

Бренд: Jaze Страницы: 102

Бренд: 2N Страницы: 2

Бренд: 3Com Страницы: 464

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды