Bosch FWI-270 Скачать руководство пользователя страница 45

Страница: 45 / 54

Radio gateway

Maintenance / troubleshooting | en

Bosch Sicherheitssysteme GmbH

Operation Manual

2019.10 | 2.0 | F.01U.373.488

Figure

7.7: Radio gateway with battery pack inserted

Holder for battery pack

Battery cable

Battery pack

LED (yellow) for trouble indication

Battery connector (3-pin)

The radio gateway is connected to the LSN line and is being supplied with auxiliary power
supply. This connection must not be interrupted while the battery is being replaced.
You have a new, undamaged battery pack BAT3.6-10 to hand.
1.

Open the housing cover.

Release the battery connector (3).

Push the holder

(1) to the side.

Remove the old battery pack

(2) and dispose of it.

Label the new battery pack with the current date (on the inscription field).

Wait until the control panel shows 'BATTERY MISSING' after 5…10

seconds.

Insert the new battery pack

(2).

Make sure that it latches into the holders correctly.

Install the battery cable

(4) as indicated by the drawing.

10. Connect the battery connector

(3).

11. Close the housing cover.

The battery pack has now been replaced.

The radio gateway is ready for operation immediately. There will be a delay before the fault
message is cleared from the fire alarm control panel.

Содержание FWI-270























































Результаты поиска

Содержание FWI-270

Отзывы:

Похожие инструкции для FWI-270

Бренды по названию

Популярные бренды

Bosch FWI-270, Руководство по эксплуатации

Результаты поиска

Содержание FWI-270

Отзывы:

Похожие инструкции для FWI-270

Бренды по названию

Популярные бренды