Bosch Evolution 500 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 60

background image

6 720 680 223

Appliance details

7

2.4

General rules to follow for safe
operation

B

1.

You must follow these instructions when you install

your heater. In the United States: The installation must
conform with local codes or, in the absence of local
codes, the National Fuel Gas Code ANSI Z223.1/
NFPA 54.
In Canada: The Installation must conform with CGA
B149.(1,2) INSTALLATION CODES and /or local
installation codes.

B

2.

Carefully plan where you install the heater. Correct

combustion  air supply and vent  pipe  installation are
very  important.  If  not  installed  correctly,  fatal
accidents  can  occur,  such  as  carbon  monoxide
poisoning or fire.

B

3.

When the unit is installed indoors and ROOM

SEALED (twin pipe) it is permitted to be located in
bathrooms, bedrooms and occupied rooms that are
normally kept closed. See chapter

3.3 (page 9). If the

unit will be installed indoors and use indoor
combustion air, the place where you install the heater
must have enough ventilation.

The National Fuel

Gas Code does not allow UNSEALED gas fired
water  heater  installations  in  bathrooms,
bedrooms  or  any  occupied  rooms  normally
kept  closed.

See chapter

3.5 (page 21) and 3.4

(

page 20).

B

4.

You must vent your heater. See

chapter 3.3 on

VENTING.

B

5.

The appliance and its gas connection must be leak

tested before placing the appliance in operation.
The appliance must be isolated from the gas supply
piping system by closing its individual manual gas
shutoff valve (not supplied with heater) during any
pressure testing at pressures in excess of ½ Psig (3.5
kPa).

B

6.

Keep water heater area clear and free from

combustibles and flammable liquids. Do not locate
the heater over any material which might burn.

B

7. Correct gas pressure

is critical for the proper

operation of this heater. Gas piping must be sized to
provide the required pressure at the maximum output
of the heater, while all the other gas appliances are in
operation. Check with your local gas supplier, and
see the section on connecting the gas supply. See
Section 3.8, page 17.

B

8.

Should overheating occur or the gas supply fail to

shut off, turn off the gas supply at the manual gas shut
off valve, on the gas line. Note: manual gas shutoff
valve is not supplied with the heater but must be field
installed.

B

9.

Do not use this appliance if any part has been

underwater. Immediately call a qualified service
technician to inspect the appliance and to replace any
part of the control system and any gas control which
has been underwater.

B

10.

Failure to install heater correctly may lead to

unsafe operation and void the warranty.

«
...
5
6
7
8
9
...
»

Содержание Evolution 500





























































Отзывы:

Нет отзывов

Похожие инструкции для Evolution 500

Бренд: Danby Страницы: 42

Бренд: Danby Страницы: 11

Бренд: Danby Страницы: 10

Бренд: Gaggenau Страницы: 68

DW60A807 Series

Бренд: Samsung Страницы: 420

Бренд: GE Страницы: 12

Бренд: Alliance Laundry Systems Страницы: 14

Бренд: GE Страницы: 3

Бренд: Fagor Страницы: 115

Бренд: Atag Страницы: 44

Бренд: Fagor Страницы: 10

Бренд: JBM Страницы: 36

Бренд: Baumatic Страницы: 29

Бренд: Hanseatic Страницы: 80

Бренд: Mach Страницы: 45

Бренд: Hansa Страницы: 40

Бренд: Hansa Страницы: 38

Бренд: GE Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды