Bosch Evolution 500 Скачать руководство пользователя страница 6

Страница: 6 / 60

6 720 680 223

Appliance details

2.3

Unpacking the heater

Before installing the unit, be certain you have the
correct heater for your type of Gas: Propane or
Natural Gas.

Identification labels are found on the

shipping box, and on the rating plate which is located on
the right side panel of the cover.

Fig. 2

Rating plate

Serial number

Type of gas

The box includes:

• Evolution 500

• Pressure relief valve (150 psi / 200,000 Btu rating)

• Bracket for wall hanging the heater

• Exhaust vent adaptor (with 4 screws and gasket

provided)

• Combustion air inlet adaptor (with 3 screws and gas-

ket provided)

• Installation manual (manual can be downloaded at

www.boschhotwater.com)

• Product registration card

• Energy Guide label.

Please complete and return the enclosed product
registration card.

The water heater is not approved or designed for:

• Manufactured (mobile) homes, boats or any mobile

installation (modular homes are acceptable for
installation)

• Use above 8000 ft A.S.L. altitude (see page 18)

• Outdoor installation without installation of Outdoor

kit (AQOK)

• Space heating purposes

• Preheated inlet water supply.

To remove front cover

Loosen the two Philips head screws located on
bottom rear of cover (see Fig. 3).

Fig. 3

Loosen the two screws

Lift front cover panel upward and remove.

Fig. 4

Removing the front cover

To remove combustion cover (service only)

Open the four clips and remove the combustion
cover see Fig. 5.

Fig. 5

Remove the combustion cover

Содержание Evolution 500





























































Результаты поиска

Содержание Evolution 500

Отзывы:

Похожие инструкции для Evolution 500

Бренды по названию

Популярные бренды

Bosch Evolution 500, Инструкция по эксплуатации

Результаты поиска

Содержание Evolution 500

Отзывы:

Похожие инструкции для Evolution 500

Бренды по названию

Популярные бренды