Bosch Evolution 500 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 60

background image

6 720 680 223

10

Installation instructions

Horizontal venting systems only:

An  optional  stainless  concentric  vent/air  intake
termination can be used to provide only one penetration
point through the exterior wall (see Fig. 8,  9 &  10). The
concentric vent/air intake kit can be ordered from your
local  wholesaler.  (Part#  ESHCK).

Note: Only tee

terminals are approved for use with the
concentric vent/air intake kit (see Table

3

). Vent

piping and tee terminal used with kit must be
from the same vent pipe manufacturer. The
appliance can also be installed with separate air
intake and exhaust piping (see Fig.

15

).

Fig. 8

Concentric kit part # ESHCK

Fig. 9

Concentric kit vent assembly

Fig. 10 Concentric kit installation

3.3.2

Venting Specifications

Install appliance as close to point of vent termination as
possible.  The exhaust  piping  must  vent  directly  to  the
outside of the structure.
Horizontal sections of vent must pitch upward towards
termination  ¼"  for  every  foot  of  horizontal  length,  to
prevent the pooling of condensate, and be supported at
4 foot intervals with overhead hangers.
Exception:  horizontal  run  between  last  elbow  and
termination  must  pitch  down  to  termination  1/4"  per
foot.  Note:  For  horizontal  terminations,  venting  must
terminate  once  it  penetrates  to  the  outside  of  the
structure.  There  must  be  no  sections  of  vent  pipe
exposed  to  the  outdoors  other  than  the  termination.
Note:  Listed  thimbles  or  collars  are  necessary  where
venting passes through wall and ceiling partitions. If the
vent system passes through combustible areas where
the vent clearance requirements cannot be maintained,
it is permissible to chase straight sections of sea led 3
inch single wall vent through 4 inch (or greater) T ype-B
vent.  The  distance  to  combustibles  using  this  chase
technique is 1 inch 1). Note: Type-B vent must never be
used  as  the  actual  exhaust  vent  system  for  the
appliance, as it is not gas tight and illegal for use with
this appliance. This will create a serious health hazard
and void the warranty.

For specific questions concerning vent material, speci-
fications, usage or installation, please contact the vent
manufacturer directly.

6720608782-09.1Av

6720608782-10.1Av

12"

6720608782-11.1Av

Min. 3 Feet

3” stainless steel pipe

3”

VENTING

Z flex

Protech

Heat Fab

3 or 4"

90° elbow

2SVEEWCF0390

FSELB9003

9314

3" Tee

Terminal

2SVSTTF03

FSTT3

9390TEE

3”

Horizontal

Terminal

2SVSTB03

FSTB3

N/A

3” Vertical

Terminal

2SVSRCF03

FSRC3

5300CI

Table 3 Terminator Part Numbers

Fittings or Piping

Equivalent

feet

m

45 degree elbow

1.25

0.38

90 degree elbow

2.5

0.76

pipe per foot

1

0.30

Table 4 Friction Loss Equivalent in piping and fittings

«
...
8
9
10
11
12
...
»

Содержание Evolution 500





























































Отзывы:

Нет отзывов

Похожие инструкции для Evolution 500

Бренд: Maytag Страницы: 88

Бренд: Indesit Страницы: 24

Бренд: Maidaid Halcyon Страницы: 15

Бренд: Asko Страницы: 59

Бренд: NEFF Страницы: 29

Бренд: Fisher & Paykel Страницы: 5

Бренд: Washtech Страницы: 12

1371236000 (0809)

Бренд: Crosley Страницы: 12

Бренд: Krowne Страницы: 47

Бренд: Gaggenau Страницы: 68

Бренд: Frigidaire Страницы: 11

Бренд: Frigidaire Страницы: 2

Бренд: Frigidaire Страницы: 2

Бренд: Frigidaire Страницы: 2

Бренд: Frigidaire Страницы: 2

Бренд: Frigidaire Страницы: 2

Бренд: Frigidaire Страницы: 12

Бренд: Frigidaire Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды