Bosch Evolution 500 Скачать руководство пользователя страница 33

Страница: 33 / 60

6 720 680 223

Maintenance and service

such as anti-freeze is not permitted as they may cause
damage to the water heater's internal components.

1. Press ON/OFF switch on the water heater to turn

OFF the heater and unplug power supply cord. The
display should be blank.

2. Shut off gas supply to heater.

3. Shut off the water supply to the water heater using

installer supplied shutoff valve.

4. Open hot water taps to drain the plumbing system. If

water continues to flow after 5 minutes, a plumbing
crossover is present and must be corrected before
proceeding.

5. Open service valves (if available) or disconnect inlet

and outlet water pipes from the water heater. Place a
small bucket underneath the water heater to catch
residual water remaining inside the water heater.

6. Using an air compressor, blow short bursts of air

(100psi max) through the outlet water connection
until there is no water present coming through the
inlet water connection of the heater.

7. Reconnect water fittings and return heater to service

when danger of freezing has past.

6.3

Mineral scale build-up

Periodic descaling may be necessary in areas with high
mineral content in the water. Scale buildup in the heat
exchanger may result in lower flow rates, error codes of
A7 and E9 and boiling sounds (knocking and banging)
in the heat exchanger.

Descaling using a pump

1. Disconnect electrical supply from the water heater.

2. Shut off the water supply to the water heater using

(installer supplied) shutoff valve.

3. Open hot water taps to drain and relieve pressure

from the plumbing system.

4. Drain water from the unit's heat exchanger by

disconnecting inlet and outlet water connections
from the heater.

5. Connect a line (A) from the outlet of the circulating

pump (installer supplied) to the inlet water fitting on
the water heater (see Fig. 54).

6. Using another line (B), connect to the water outlet

fitting on the water heater. Route the other end of this
line into a descaling reservoir.

7. Using a 3rd line (C) from the descaling reservoir,

connect to the inlet side of circulating pump. Install a
filter on the end of this line in the descaling reservoir.

8. Make sure all connections are "water tight.".

9. Fill tank with descaling solution so both lines inside

are submersed. We recommend straight white
vinegar. If using a commercial descalant, refer to
manufacturer's instructions on dilution with water.

10.Operate the circulating pump.

11.Make sure there are no leaks and the solution is

flowing from the descaling reservoir through the
heater and returning to the reservoir.

12.Run solution through the heater until the solution

returning to the descaling reservoir comes out clear.
(Changing to a fresh solution may be necessary
during this process).

13.Disconnect all lines and drain all solution from heat

exchanger. Properly discard of solution.

14.Position a container below the hot water outlet and

connect cold water supply. Open cold water supply
isolation valve and flush heat exchanger with clean
water.

15.Shut cold water shutoff valve and reconnect hot

water supply to the water heater.

16.Reconnect electrical supply to unit, open water

shutoff valves, and return the unit to service.

Fig. 54

6.4

Adjusting CO

(carbon dioxide)

The CO

can only be adjusted by a certified gas

technician with a calibrated CO

analyzer.

Static Gas Pressure:

“ WC

P1 Operating Pressure:

“ WC

The P1 minimum operating gas pressure is 3.5" WC for
Natural Gas and 8" WC for Propane. Do not proceed in

Caution:

One factor that may affect

levels is improper gas pressure.

Please see Chapter 3.12 for the
procedure to measure gas pressure
and record your findings below:

Содержание Evolution 500





























































Результаты поиска

Содержание Evolution 500

Отзывы:

Похожие инструкции для Evolution 500

Бренды по названию

Популярные бренды

Bosch Evolution 500, Инструкция по эксплуатации

Результаты поиска

Содержание Evolution 500

Отзывы:

Похожие инструкции для Evolution 500

Бренды по названию

Популярные бренды