Bosch Evolution 500 Скачать руководство пользователя страница 5

Страница: 5 / 60

6 720 680 223

Appliance details

2.2

Specifications (Technical data)

Approved in US/Canada

Capacity

Maximum flow rate: 7.15 GPM (27 l/min) at a 45°F
(25°C) rise.

Maximum output

160,500 Btu/h (47.0 kW)

Maximum input

195,000 Btu/h (57.1 kW)

Efficiency in %

Thermal efficiency > 82%

Min. Input

19,900 Btu/h (5.8 kW)

Temperature Control

Selection range: 100°F (38°C) - 140°F (60°C)

Default temperature: 122°F (50°C)

Stability: +/- 2°F (+/- 1°C)

Gas Requirement

Gas connection (inches) - ¾”

Inlet gas pressure under operation (with a high hot
water flow rate)*

• Propane: 8” - 13” water column

• Natural Gas: 3.5” - 10.5” water column.

* To measure gas pressure, see Measuring Gas
Pressure, chapter 3.12.

Water

• Hot water connection (inches) - ¾”

• Cold water connection (inches) - ¾”

• Water valve material: Polymer (PPS) (Polypropylene

Sulfid)

• Minimum water flow: 0.65 gallon/minute (2,5 l/m).

Note: Activation varies with inlet water temperatures
from 0.65 - 1.6 gallon/minute.

• Minimum recommended water pressure: 30 PSI

(2.07 bar)

• Minimum recommended well pressure: 40 PSI (2.75

bar), see chapter 3.9.

• Connections:

– Bottom of heater

Combustion

• NOx

≤

40 Ng/J

(Nanograms of NOx (calculated as NO2) per

Joule of heat output).

• CO

≤

250 ppm (measured)

• CO

level set from factory, see chapter 6.4.

Dimensions

• Depth (in): 11¼” (286 mm)

• Width (in): 17

” (452 mm)

• Height (in): 30½” (775 mm)

• Weight: 67 pounds (30,5 kg).

Gas types

Natural Gas.
LP Gas.
Converting the gas type can only be done by a certified
gas technician with a calibrated CO

analyzer.

Call

Bosch

Water

Heating

through

Bosch

thermotechnology corp.

for conversion instructions.

Voltage

120 V AC (60 Hz) nominal

Amperage

Idle - 40 mA
Operation -

≤

2.5 A

Noise

45 - 65 db (A)

Safety devices

• Flame failure device (ionization flame rod sensor)

• Pressure relief valve (supplied with heater)

• Over heat prevention (temperature limiter)

• Inlet temperature sensor

• Outlet temperature sensor

• Backflow temperature sensor.

Water protection

IP X4 (protection against water drops)

If appliance is installed at elevations above
2000ft, refer to section 3.3.6 Fan speed
adjustment.

Содержание Evolution 500





























































Результаты поиска

Содержание Evolution 500

Отзывы:

Похожие инструкции для Evolution 500

Бренды по названию

Популярные бренды

Bosch Evolution 500, Инструкция по эксплуатации

Результаты поиска

Содержание Evolution 500

Отзывы:

Похожие инструкции для Evolution 500

Бренды по названию

Популярные бренды