Bosch Evolution 500 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 60

background image

6 720 680 223

26

Installation instructions

the water heater as possible. See Fig. 31. To install the
PRV, a suitable fitting connected to an extension on a
“T” fitting can be sweated to the hot water line.
Support all piping.

Fig. 31 Plumbing Connections (with shutoff valves)

and Pressure Relief Valve

1

Water filter

3.11 Domestic hot water recirculation

Although  recirculation  directly  through  the  tankless
water  heater  is  allowed,  temperature  stability  is
improved by recirculating through a mini-tank as shown
in Fig. 32.  By using  the design  in  Fig.  32,  there  is  no
recirculation  of  hot  water  through  the  tankless  water
heater  and  therefore,  does  not  affect  the  heat
exchanger  warranty.  Direct  recirculation  through  the
tankless water heater is permissible, however, the heat
exchanger  warranty  is  reduced;  contact  Bosch
Thermotechnology for further installation requirements.
The  following  drawing  is  provided  to  outline  one
possible recirculation design using the water heater in
conjunction with an Ariston mini tank water heater. This
schematic is for illustration only and must not be used
for  actual  installation  without  appropriate  engineering
and  technical  advice  from  a  properly  licensed
professional  in  the  locality  where  the  installation  is
made.

Fig. 32 Recirculation application

1

Full port isolation valve

2

Circulator (pump)

3

Check valve

4

PRV

5

Expansion tank

The use of a small electric mini-tank water heater (4-6
gallon  size)  should  be  used  for  this  application  and
designed so the pump will circulate the water through
the  mini-tank  and  the  building's  hot  water  return  loop
only.  Timed  or  thermostatically controlled operation of
the  pump  is  commonly  done.  Contact  Bosch
Thermotechnology if further information is needed.

3.12 Measuring gas pressure

Confirm gas pressure upon installation.

Connecting manometer

B

Shut off gas supply at installer supplied shutoff valve
for this water heater.

B

Remove front cover and locate inlet gas pressure
measuring point (see Fig. 34).

B

Loosen screw inside left test point fitting (do not
remove) and connect manometer tube to test point.
Remove screw completely if correct size tapping is
available.

Static Pressure Test

B

Turn gas supply back on.

B

Record static gas pressure reading in table 15.

Operating Pressure Test

B

Press ON/OFF button to turn off the appliance.

6720608158-77.1AL

1

4

5

3

2

Ariston Minitank

Evolu-

tion

500

«
...
24
25
26
27
28
...
»

Содержание Evolution 500





























































Отзывы:

Нет отзывов

Похожие инструкции для Evolution 500

Built-In Dishwasher

Бренд: GE Страницы: 32

Бренд: Dacor Страницы: 24

Бренд: Dacor Страницы: 2

Бренд: Dacor Страницы: 3

Бренд: Dacor Страницы: 24

Бренд: Dacor Страницы: 28

Бренд: davoline Страницы: 68

Бренд: ZANKER Страницы: 28

Appliances Profile PFWS4605

Бренд: GE Страницы: 88

Бренд: Galanz Страницы: 14

Бренд: Perlick Страницы: 16

Бренд: Hotpoint Страницы: 16

Бренд: Gorenje Страницы: 24

Бренд: WESCO NAVY Страницы: 186

Бренд: Gaggenau Страницы: 24

HG6085D137609HW

Бренд: Hanseatic Страницы: 78

Бренд: FAR Страницы: 58

Бренд: Fagor Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды