Bosch Evolution 500 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 60

background image

6 720 680 223

Installation instructions

13

Required other than direct vent terminal clearances (single pipe penetration)

Fig. 12

*

For clearances not specified in ANSI Z223.1 / NFPA 54 or CSA-B149.1, one of the following shall be indicated:
a) A minimum clearance value determined by testing in accordance with section 2.20, or;
b) A reference to the following footnote:
“Clearance in accordance with local installation codes and the requirements of the gas supplier.”

6720608836-23.1Av

Canadian installations

1)

U.S. installations

2)

A

Clearance above grade, veranda, porch, deck or balcony

12 in.

12 in.

B

Clearance to window or door that may be opened

36 in.

4 feet below or to side of opening;

1 foot above opening

C

Clearance to permanently closed window

*

*

D

Vertical clearance to ventilated soffit located above the vent
terminator within a horizontal distance of 2 feet (61cm) from the
center line of the terminator

*

*

E

Clearance to unventilated soffit

*

*

F

Clearance to outside corner

*

*

G

Clearance to inside corner

*

*

H

Clearance to each side of center line extended above meter/
regulator assembly

36 in. within a height 15 feet above

meter/ regulator assembly

*

I

Clearance to service regulator vent outlet

36 in.

*

J

Clearance to non-mechanical air supply inlet to building or the
combustion air inlet to any other application

36 in.

4 feet below or to side of opening;

1 foot above opening

K

Clearance to mechanical air supply inlet

72 in.

36 in. above if within 10 feet

horizontally

L

Clearance above paved sidewalk or paved driveway located on
public property

84 in.

3)

84 in.

M

Clearance under veranda, porch deck or balcony

12 in.

4)

*

Table 8

1)

In accordance with the current CSA B149.1 Natural Gas and Propane Installation Code

2)

In accordance with the current ANSI Z223.1 / NFPA 54 National Fuel Gas Code

3)

A vent shall not terminate directly above a sidewalk or paved driveway that is located between two single family dwellings and serves both dwellings.

4)

Permitted only if veranda, porch, deck or balcony is fully open on a minimum of two sides beneath the floor.

«
...
11
12
13
14
15
...
»

Содержание Evolution 500





























































Отзывы:

Нет отзывов

Похожие инструкции для Evolution 500

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 43

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 18

Бренд: Campomatic Страницы: 25

Бренд: Gaggenau Страницы: 2

Бренд: Omega Страницы: 6

Бренд: GE Страницы: 28

Бренд: Proline Страницы: 18

Бренд: INVENTOR Страницы: 68

Бренд: NEFF Страницы: 32

Бренд: Galanz Страницы: 32

Бренд: Asko Страницы: 32

HG6085D137609HW

Бренд: Hanseatic Страницы: 78

Бренд: Kuppersberg Страницы: 96

MDC4650AWB - Jet Clean II 24" Portable Dishwasher

Бренд: Maytag Страницы: 2

Бренд: Samsung Страницы: 88

Бренд: Samsung Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды