Bosch AUTODOME inteox 7000i 2MP Скачать руководство пользователя

Страница: 33 / 66

AUTODOME inteox 7000i - 2MP (pendant)

Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts | en

Bosch Security Systems

Installation Manual (pendant)

2020-07 | 1.0 |

Attach the Pendant Arm to the Mounting Plate

The bottom hinge pin of the Pendant Arm is provided with a Hinge Pin Stop to hold the hinge
open while attaching the arm to the Mounting Plate.
1.

Compress the bottom hinge pin by pushing the pin lever downward and rotating it behind
the Hinge Pin Stop.

Figure 9.9:

Connect Pendant Arm to Mounting Plate

Open the top hinge by pushing its pin lever up and holding it.

Note

: Both Hinge Pins must be fully compressed to open (unlock) the hinges of the

Pendant Arm and before proceeding to the next step.

While continuing to hold the top hinge pin open, align the top and bottom hinges of the
Pendant Arm to their mating points on the Mounting Plate.

Once you have the hinges aligned, release the top hinge pin to engage its mating hinge on
the Mounting Plate. Then release the bottom hinge pin from the Hinge Pin Stop to lock
the Pendant Arm to the Mounting Plate.

Route and Connect Wires to a Power Supply Box

The illustration below depicts the power and control cables connected to the Pendant Arm:

Figure 9.10:

Pendant Arm Cables

Cable

Grounding Strap (black)

UTP Video/Ethernet (blue)

Содержание AUTODOME inteox 7000i 2MP



































































Результаты поиска

Содержание AUTODOME inteox 7000i 2MP

Отзывы:

Похожие инструкции для AUTODOME inteox 7000i 2MP

Бренды по названию

Популярные бренды

Bosch AUTODOME inteox 7000i 2MP, Руководство по установке

Результаты поиска

Содержание AUTODOME inteox 7000i 2MP

Отзывы:

Похожие инструкции для AUTODOME inteox 7000i 2MP

Бренды по названию

Популярные бренды