Bosch AUTODOME inteox 7000i 2MP страница 21 Скачать руководство пользователя | Manualshive

Страница: 21 / 66

background image

AUTODOME inteox 7000i - 2MP (pendant)

Mount Power Supply Box (Wall, Mast (Pole), and Corner Mounts) | en

21

Bosch Security Systems

Installation Manual (pendant)

2020-07 | 1.0 |

8

Mount Power Supply Box (Wall, Mast (Pole), and

Corner Mounts)

Before mounting the Power Supply Box, decide if you should wire the box through the holes in
the bottom or back of the box. If wiring the box through the back, move the two (2) seal plugs
to the bottom through the holes before mounting.

Notice!

Use 3/4-inch (20-mm) NPS fittings for the holes on the bottom and back of the box. Use 1/2-
inch (15-mm) NPS fittings for the side holes.

Figure 8.1:

Power Supply Wall, Mast (Pole), and Corner Mounts

1.

Use the wall mount template supplied in the packaging box to locate the four (4)
mounting holes for the Power Supply Box.

2.

Drill four (4) holes for the mounting anchors. If installing outdoors, apply a weatherproof
sealant around each hole at the mounting surface.

!

Warning!

A stud diameter of 6.4 mm (1/4 inch) to 8 mm (5/16 inch) able to withstand a 120 kg (265 lb)
pull-out force is recommended. The mounting material must be able to withstand this pull out
force. For example, 19-mm (3/4-inch) minimum for plywood.

3.

Secure the Power Supply Box to the mounting surface.
For a Wall installation: Use four (4) corrosion-resistant, stainless steel studs (not
supplied). Then proceed to Step 5 below.
For a Corner installation: Secure the Corner Plate to the wall corner using four (4) studs
(not included). Then proceed to Step 5 below.
For a Mast or a pole installation: The metal straps included with the Mast mount
accommodate a pole with a diameter of 100-380 mm (4-15 in.). You must use a banding
tool (sold separately) for a mast or pole installation. Follow the instructions provided
with the banding tool to securely mount the Mast Plate to the pole. Contact your Bosch
Sales Representative to order Banding Tool P/N TC9311PM3T.

4.

Secure the Power Supply Box to the Corner Plate or Mast Plate using the four (4) 3/8 x
1-3/4-inch bolts and split lock washers (supplied).

5.

Attach 3/4-inch (20-mm) NPS watertight, earth-grounded conduit pipe fittings (not
supplied) to the bottom or back holes of the Power Supply Box through which you will
run the power, video, and control data wires.

«
...
19
20
21
22
23
...
»

Содержание AUTODOME inteox 7000i 2MP



































































Отзывы:

Нет отзывов

Похожие инструкции для AUTODOME inteox 7000i 2MP

Бренд: Yoko Technology Страницы: 58

Бренд: Edimax Страницы: 11

Бренд: Uniden Страницы: 6

Бренд: Wonwoo Страницы: 19

Бренд: Aluratek Страницы: 24

Бренд: Digitus Страницы: 2

ZD15 - Easyshare Zoom Digital Camera

Бренд: Kodak Страницы: 74

NightHawk 26-0900

Бренд: Bushnell Страницы: 2

Бренд: Walimex Pro Страницы: 32

Бренд: Polaroid Страницы: 16

Pro Travel Premium

Бренд: Lifetrons Страницы: 2

Бренд: Dsoon Страницы: 89

Бренд: Basler Страницы: 2

Бренд: iBeam Страницы: 8

Бренд: Vivitar Страницы: 29

Бренд: VistaQuest Страницы: 10

Бренд: Ability Страницы: 44

Бренд: myGEKOgear Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды