Bosch AUTODOME inteox 7000i 2MP Скачать руководство пользователя

Страница: 59 / 66

AUTODOME inteox 7000i - 2MP (pendant)

Connection | en

Bosch Security Systems

Installation Manual (pendant)

2020-07 | 1.0 |

Audio Line Level Output Connections

Connect the audio line level input of the audio output device (for example, an amplified
speaker or a PC line level input) to the Au (RXD) output terminal.

Connect the audio line level output signal ground to the Audio_Out- (TXD) output
terminal.

Figure 13.6:

Connections for audio over an Ethernet network

Audio_In- (C-)

AUTODOME Data In/Out

A (C+)

P105/P106 Connector

Earth Ground

Audio Out

Au (RXD)

Audio_Out– (TXD)

Signal Ground

Notice!

Separate the audio cables from the AC power lines to avoid noise.

To configure audio on the camera, refer to Basic Mode: Audio or Audio.

Содержание AUTODOME inteox 7000i 2MP



































































Результаты поиска

Содержание AUTODOME inteox 7000i 2MP

Отзывы:

Похожие инструкции для AUTODOME inteox 7000i 2MP

Бренды по названию

Популярные бренды

Bosch AUTODOME inteox 7000i 2MP, Руководство по установке

Результаты поиска

Содержание AUTODOME inteox 7000i 2MP

Отзывы:

Похожие инструкции для AUTODOME inteox 7000i 2MP

Бренды по названию

Популярные бренды