manualshive.com logo in svg

Bosch AUTODOME inteox 7000i 2MP, Руководство по установке

Поделиться
Скачать
Bosch AUTODOME inteox 7000i 2MP Скачать руководство пользователя страница 19

AUTODOME inteox 7000i - 2MP (pendant)

(Optional) Installing an SD Card | en

19

Bosch Security Systems

Installation Manual (pendant)

2020-07 | 1.0 |

6

(Optional) Installing an SD Card

The camera can accept a customer-supplied 

SDHC

 or 

SDXC

 memory card (hereafter referred

to as “SD card”) for local storage. (The camera will not accept MicroSD cards.) Using an 

SD

card is optional.

Note:

 Disconnect power to the camera while adding or removing an 

SD

 card.

1.

Follow the steps in one of these sections (depending on the type of camera mount):
Remove bubble from in-ceiling housing or Remove bubble from pendant housing.

2.

Slide the SD card into the slot. Press down the end of the SD cards until you hear a click
and the card locks into place.

3.

Follow the steps in one of these sections (depending on the type of camera mount):
Replace the bubble in an in-ceiling housing or Replace the bubble in a pendant housing.

Содержание AUTODOME inteox 7000i 2MP



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды