background image

 

 

 

 

20 

 

 

SCORPION DCS QX45 User Manual_

January 2014 Edition

 

 

 

Abrasive assembly procedures 

 

SCORPION DCS QX45 Expansion (centrifugal drum)

 

 

Fit the abrasive disc to the drum ensuring that the abrasive 
protrudes approximately 1.5 mm from the drum itself. 
 
 

 

 

 

 

 

 

 
CAUTION 

 

Do not start the machine without the 
abrasive inserted, 
otherwise the drum will be damaged and 
must be replaced. 

 

 

 

 

 

 

WARNING 

The  abrasive  is  in  the  correct  position  when  it  protrudes  approximately  1.5  mm 
from the sander drum. 

 

HAZARD 

Using a damaged abrasive which could then tear while sanding may damage the 
machine or floor.

 

 

SCORPION DCS QX45 EasyFit (with bubble mat surface) 

 

Loosen  the  paper  press  screws  on  the  drum  with  the  correct  screwdriver,  being  careful  not  to  remove  the 
screws and paper press from the drum. 

        

          

 

 

Insert one end of the abrasive under the paper press. Turn the drum so the abrasive winds around the drum itself. 
Insert the other end of the abrasive under the paper press. Centre the abrasive on the drum and smooth out any 
creases.  Tighten  the  paper  press  screws  carefully.  If  unsure  loosen  the  paper  press  screws  and  repeat  the 
procedure. 

 

 

HAZARD 

An  abrasive  which  is  not  stretched  correctly  or  is  damaged  could  tear  while 
sanding and damage the machine or floor.

 

Содержание Scorpion DCS






























Отзывы: